Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Tubo de Teflon para cola

18/10
Valoración 

Tubo de teflón para eje de cola

11,50 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción

Tubo de teflón para eje de cola

Detalles del producto
18/10
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Tubo de Teflon para cola

Tubo de Teflon para cola

Tubo de teflón para eje de cola

Escriba su propia reseña
16 other products in the same category:

Reference: 97/9

Screw fitting pushrod connector

Review(s): 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Price 4.40€
More
On sale upon request

Reference: 3936/1

Y-lead

Review(s): 0

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Price 13.10€
More
On sale upon request

Reference: 3944

Servo mount 120°

Review(s): 0

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Price 14.20€
More
On sale upon request

Reference: 8/3

Tail rotor flange

Review(s): 0

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Price 8.30€
More
On sale upon request

Reference: 33/20

Rotor blade support

Review(s): 0

An easy solution to the transport problem: This rotor blade support fits all helicopter trainers with 20 mm O.D. tail booms.Rotor blade supportfor rotor blades up to 65 mm chord

Price 11.70€
More
On sale upon request

Reference: 74

O-ring 3 x 8 mm hard

Review(s): 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Price 3.90€
More
On sale upon request

Reference: 33/25

Rotor blade support

Review(s): 0

Any easy solution to the transport problem: The cut-out of this rotor blade support accommodates to the different shapes of tail booms on fuselages.Rotor blade supportfor fuselages, 30 x 270 x 200 mm

Price 20.50€
More
On sale upon request

Reference: 330/10

Cabin sheath for Lama

Review(s): 0

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Price 50.20€
More
On sale upon request