Referencia: 92/91
Rodamiento con orejuela de 6 x 10 x 3 mm
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Référence: 33/22
If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...
Référence: 10/1
Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.
Référence: 97/9
Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...
Référence: 8/3
The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...
Référence: 18/11
Aluminium tube 5.5 x 4.4 x 1000 mm
Référence: 333/5
bag length: 120 cmmax. blade width: 9.5 cm
Référence: 3948
Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30
Référence: 330/10
This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400
Référence: 330/18
Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3
Référence: 18/10
PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm
Référence: 603/19
Component part for fuselages, Ord.No. 6030 or 6031.
Référence: 3944
When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...
Référence: 33/25
La bonne solution pour le transport: La découpe du grand support convient aux différentes formes des poutres sur les fuselages.Support de transportpour fuselages, 30 x 270 x 200 mm