Espejo (largo) Lama 1:4

Reference: 341/416

Espejo Lama 1: 4

Reference: 341/507

Oil tank large Lama 1:4

dimensions: 5.15 x 3.62 x 5.1 cm

Reference: 340/40

Mirror set for large-scale models

Mirror set, complete as illustratede.g. for Lama and other large-scale modelsdimensions of the mirrors: approx. 40 x 84 and 14 x 22 mm

Reference: 330/45

Hook for Lama

The hook for the Lama is fully functional. The scale aluminium frame comes with further more accessories, inclusive servo mount.The fuselage already offers the fastening, ready soldered.On your model you mount the hook in the required location, and release dummy loads by activating a servo via your transmitter.

Reference: 330/2

Dummy turbine, GRP

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Reference: 1/21

Helmet for pilot William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Reference: 341/411

Llama estabilización trasera 1: 4

Reference: 330/36

Door latch for Lama

If you don't want that the doors of the Lama canopy close itself after opening, you use these magnet latches.

Reference: 330/5

Fittings set Bell 47 G III, Lama

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Reference: 341/424

Kick bar llama 2 partes 1: 4

Reference: 341/409

BTP Lama 1: 4

Reference: 134/460

Telephone on board 1:4

dimensions: 1.9 x 1.2 x 6.3 cm

Reference: 341/406

Electric Box Lama 1:4

dimensions: 12.6 x 7 x 4.3 cm2-part

Reference: 350/17

Exhaust cover, Ø 90 mm

When the turbine of a full-size helicopter is not running, the engine is protected with an exhaust cover which prevents foreign objects finding their way inside the turbine. This exhaust cover for model turbines is suitable for the Lama, Alouette III and any other machine with a 90 mm Ø exhaust pipe. Caution: it is essential to allow the exhaust pipes to...

Reference: 340/6

Entry step, for Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Reference: 340/13

Dummy power unit

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...