Retroviseur grand Lama 1:4

Référence: 330/36

Fixation de portes

If you don't want that the doors of the Lama canopy close itself after opening, you use these magnet latches.

Référence: 340/1

Support de roue pour Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Référence: 134/411

Antena alrededor de 1: 4

Référence: 340/13

Transmission factice

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Référence: 340/5

Protection contre l'enlisement pour Lama

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Référence: 341/416

Espejo Lama 1: 4

Référence: 341/406

Boitier électrique Lama 1:4

dimensions: 12.6 x 7 x 4.3 cm2-part

Référence: 341/415

Llamada de rescate por radar x2 1: 4

Référence: 134/444

Winch connections 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Référence: 340/2

Accessoires maquette pour Lama turbine

The suckering ducts are on the model exactly on the same place as the original ones in position to the turbine on the full-size helicopter.

Référence: 341/404

Feux de position Lama x2 1:4

dimensions: 4.5 x 3.2 x 1.8 cmPack of 2 (l/r)

Référence: 330/10

Housse de protection pour Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Référence: 341/419

Poulies de cables Lama x6 1:4

1,18 x 3,15 x 0,72 cmPack of 6

Référence: 340/6

Marchepied, pour Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Référence: 330/45

Crochet pour Lama

The hook for the Lama is fully functional. The scale aluminium frame comes with further more accessories, inclusive servo mount.The fuselage already offers the fastening, ready soldered.On your model you mount the hook in the required location, and release dummy loads by activating a servo via your transmitter.

Référence: 341/508

Petit reservoir d'huile Lama 1:4

dimensions: 5.45 x 1.66 x 5.36 cm