
Referencia: 92/91
Rodamiento con orejuela de 6 x 10 x 3 mm
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Reference: 703/30
Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...
Reference: 1005/60
Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...
Reference: 702/75
With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....
Reference: 704/36
Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...
Reference: 1005/12
The basic method of operation of the turbine-powered Bell 212's rotor head is the same as that of the Bell 47 G III rotor head. The main difference is that the components have been modified to match the appearance of the Bell 212, and are therefore of different design. For example, a separate swashplate driver is not required, as it is integrated into the...
Reference: 704/35
Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...
Reference: 1005/50
The Sky Fox rotor head in its original form is robust and very sturdy, so it can achieve good results in all flight positions.The rotor head is supplied with a ball raced pitch compensator and two main shaft collars, their use depends on the length of the rotor shaft.CautionIt is not permissible to use this rotor head on a mechanical system powered by a...
Reference: 702/70
This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...
Reference: 703/39
Lama Scale Rotorhead: for the large Vario LamaWe have now finalized our tests with the Starwood Lama scale rotorhead on the Vario Lama 1:4. Now we are proud to present to you under the Ord.No. 703/39, a truly Scale rotor head including all necessary parts in order to mount this head on the Vario Lama.The head is available now. The kit includes the...
Reference: 705/30
Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...
Reference: 703/43
The take-off weight of our large Alouette III is relatively high, and we therefore decided to revise the linkage for the XL-C rotor head and the 3-blade rotor head in order to optimise the system...
Reference: 702/80
The UH-1D or UH-1B models with an excessive length of the rotor shaft out of the mechanics fly for safety reasons with rotor shafts of 12 mm Ø. The difference between the SKS semi-scale rotor heads on offer is due to the centre hub. This version fits the shaft diameter of 12 mm.We recommend this rotor head for experenced pilots only.The performance of...