Rotulas ancha para varilla 2.5 mm

Reference: 107/23

Ball-links 2.5 mm for ballrace

 Content of the package6 pieces

Reference: 060/2

Ball-end bolt 5.0 mm - M 3.0 x 3.0

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 060/23

Ball-end bolt 5.0 mm - M3.5 x 3.0

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 060/14

Ball-end bolt 9.5 mm - M 3.0 x 3.0, dia 5.5 mm

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 060/55

Ball-end bolt 3.5 mm - M 2.5 x 7.0

Not available

Reference: 80/21

Ball retainer set

Ball joints, especially on helicopters that are flown actively by 3-D pilots, are subject to very strong forces. Due to necessary large control movements the ball joints can stretch over a period...

Reference: 060/15

Ball-end bolt 3.5 mm - M 2.0 x 3.5

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 060/7

Ball-end bolt 3.5 mm - M 2.5 x 5.0

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 060/5

Ball-end bolt 20.0 mm - M 3.0 x 7.0

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 107/17

Ball-links 2.5 mm

Reference: 107/49

Ball-links 3.0 mm

Pack of 25

Reference: 107/10

Ball link 2.0 mm

Pack of 25

Reference: 107/15

Ball link 3.0 mm

It is advisable to use stronger pushrods and balls with a larger diameter on demand. This combination often is selected by the pilots with airplanes as well.Ball-link for 3.0 mm pushrodpack of 10connector fits 5.5 mm ��balls

Reference: 060/17

Ball-end bolt 13.0 mm - M 3.0 x 9.0

In our range of products we provide ball-end bolts made of hard-chromed steel with an excellent surface quality, and with different ball sizes, but mainly used are those with a diameter of 4.8 mm. Please check before you order that you have selected the correct ball-end bolt. Measure the ball, the diameter and the length of the thread to be on the safe...

Reference: 107/8

Ball-links 2.0 mm

Ball joints for 2.0 mm thread are only applied at the tail rotor if the one piece control bridge Ord.No 100 is used. Contend of the package: 10 pieces.

Reference: 060

Ball-end bolt 3.5 mm - M 2.0 x 5.0

These ball-end bolts offer an optimal connection between a GRP servo output arm and the pushrod to the mechanics. Underneath the output arm you lock the ball-end bolt with an M 2 hexagon nut. For aluminium output arms you use ball-end bolts Ord.No. 060/7 and thread-lock fluid.