Marcas

Ninguna marca

Proveedores
Los productos más vendidos

Rotulas de driver 5.5

107/1
Valoración 
Hexagonales de enlace 5,5
8,40 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Hexagonales de enlace 5,5
Detalles del producto
107/1
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Rotulas de driver 5.5

Rotulas de driver 5.5

Hexagonales de enlace 5,5
Escriba su propia reseña
16 altri prodotti della stessa categoria:

Riferimento: 70/21

Die M 2.0 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 54,60 €
Più
In vendita su richiesta

Riferimento: 9/11

Three-armed gripper

Recensioni: 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Prezzo 11,70 €
Più
In vendita su richiesta

Riferimento: 11/84

Assembly spanner

Recensioni: 0

If you want to extract the flywheel and the split tapper collet from the motor you hold the flywheel with the assembly spanner while you turn in the extractor screw.

Prezzo 12,80 €
Più
In magazzino

Riferimento: 107/2

Ball-link driver 4.0

Recensioni: 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Prezzo 8,40 €
Più
In vendita su richiesta

Riferimento: 10/77

Sanding sponge

Recensioni: 0

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Prezzo 5,50 €
Più
In vendita su richiesta

Riferimento: 21/11

Tool case

Recensioni: 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prezzo 19,10 €
Più
In vendita su richiesta

Riferimento: 70/20

Die M 2.5 HSS

Recensioni: 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prezzo 46,10 €
Più
In vendita su richiesta

Riferimento: 64/2

Flywheel puller

Recensioni: 0

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Prezzo 11,20 €
Più
In vendita su richiesta

Riferimento: 11/64

Hole cutter up to 16 mm Ø

Recensioni: 0

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Prezzo 54,60 €
Più
In vendita su richiesta

Riferimento: 90/7

Hammer, weight 230 g

Recensioni: 0

How do you fix anything to a wooden component using a metric machine screw? The answer is to fit a captive nut as follows: Drill a hole of the right size to accept the nut barrel, then drive the nut's projecting teeth into the wood using a hammer and fairly gentle force; the captive nut is correctly fitted when its disc rests squarely on the surface of...

Prezzo 27,40 €
Più
In vendita su richiesta

Riferimento: 9/5

Protective goggles

Recensioni: 0

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Prezzo 14,80 €
Più
In vendita su richiesta

Riferimento: 11/56

Glasspaper file, concave / convex

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 12,80 €
Più
In vendita su richiesta

Riferimento: 11/86

Pushrod measuring holder

Recensioni: 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prezzo 14,80 €
Più
In vendita su richiesta

Síganos en Facebook