Accueil
Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 420 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 97-108 de 420 article(s)

Filtres actifs

Réservoir en Kevlar 1.4 l... Aperçu rapide

Référence: 26/50

Réservoir en Kevlar 1.4 l pour Kérosène et pétrole

Commentaire(s): 0

Aramid is a fibre that is used in motor racing. The tanks have an even surface inside and rough on the outside. These fuel tanks are all pressure tested to make sure that they are 100% leak-proof when they arrive at your workshop. They fit in every fuselage, that would normally use the plastic tank Ord.No. 26/5 for. For example, this Aramid tank is...

Prix 349,10 €
Détails
En vente sur demande
Motor mount drilled for... Aperçu rapide

Référence: 59/2

Motor mount drilled for Rossi 11.5 cc

Commentaire(s): 0

Factory-drilled motor mounts, already drilled and tapped for M 3 or M 4, are available in pairs (left / right). Avoid interchanging the left hand with the right hand one!1 pairfactory-drilled

Prix 54,60 €
Détails
En vente sur demande
Tube PTFE 20 x 2,5 x 100 mm Aperçu rapide

Référence: 115/11

Tube PTFE 20 x 2,5 x 100 mm

Commentaire(s): 0

Manifolds and tuned pipes or silencers must be installed without touching each other, because the contact of these metal parts could cause radio interference. We can refer to this interference as "electric noise". The connection by PTFE pipe enables the required distance of 10 - 15 mm in the prescribed position, and it steadily seals gas-tight. This...

Prix 19,40 €
Détails
En vente sur demande
Shim spacer set Aperçu rapide

Référence: 59/20

Shim spacer set

Commentaire(s): 0

To obtain the optimum clearance between clutch pinion and main gear you can use these shim spacers, which are 0.1 and 0.2 mm thick. Simply loosen the engine retaining screws and place the appropriate shim spacer between engine and engine mount; suits all types of engine.Engine spacer set2 each 0.1 mm and 0.2 mm thick

Prix 11,20 €
Détails
En vente sur demande
Exhaust for Bell 212 Twin Jet Aperçu rapide

Référence: 214/16

Exhaust for Bell 212 Twin Jet

Commentaire(s): 0

Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.

Prix 552,50 €
Détails
En vente sur demande
Tuned pipe silencer Aperçu rapide

Référence: 116/65

Tuned pipe silencer

Commentaire(s): 0

 Tuned pipe silenceroverall length 350 mmconnection-Ø 20 mmoverall Ø 50 mmsilencer chamber 170 mmweight approx. 160 gtail pipe length 90 mmcurved, for UH-1D

Prix 153,40 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook