Accueil
Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Compensateur de pas Ø 10 mm

71/20
Note 

Pitch compensator, complete, for 10 mm ∅ main shaft, centre piece GRP

75,60 €
TTC
Quantité
En vente sur demande

 

Política de seguridad

 

Política de envío

 

Política de devolución

Description

Pitch compensator, complete, for 10 mm ∅ main shaft, centre piece GRP

Détails du produit
71/20
Avis

Aucun avis n'a été publié pour le moment.

Donnez votre avis

Compensateur de pas Ø 10 mm

Compensateur de pas Ø 10 mm

Pitch compensator, complete, for 10 mm ∅ main shaft, centre piece GRP

Donnez votre avis
16 altri prodotti della stessa categoria:
Inertia weights for Ø 5 mm... Anteprima

Riferimento: 79/8

Inertia weights for Ø 5 mm flybar

Recensioni: 0

Inertia weights are small "extra brakes". They increase the gyroscopic stability of the flybar and slow down the rotor head's response. For every beginner we recommend these so the responsiveness of the rotor head is reduced. The rotor head becomes more responsive as the inertia weights are moveded inwards (always place equally!). Inertia weights suitable...

Prezzo 30,60 €
Più
In vendita su richiesta
Mixer lever cranked Anteprima

Riferimento: 78/41

Mixer lever cranked

Recensioni: 0

Mixer lever, content of the package 1 piece.Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative. The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole. Please note for choosing the screws:...

Prezzo 17,00 €
Più
In vendita su richiesta
4-blade centre piece 12 mm Anteprima

Riferimento: 704/33

4-blade centre piece 12 mm

Recensioni: 0

Component part for a multi-blade rotor head for 12 mm Ø main shaft; see Ord.No. 703/32, 704/32 resp. 705/32.

Prezzo 299,50 €
Più
In vendita su richiesta
Rotor head dampers for 2... Anteprima

Riferimento: 74/7

Rotor head dampers for 2 blade FBL systems

Recensioni: 0

Flybarless electronics have now become common. Where they are being used harder damping is required.For these cases Vario is now offering a harder damping of the blade shaft provided by a pretension absorbing element in the centre block.For the adjustment, the outer O-ring position can be selected between "hard" and "soft" flight characteristics.Important...

Prezzo 30,60 €
Più
In vendita su richiesta
Shaft bearing Anteprima

Riferimento: 72/32

Shaft bearing

Recensioni: 0

Shaft bearing Content of the package: 1 piece

Prezzo 17,00 €
Più
In vendita su richiesta
GRP blade holder, 22 mm... Anteprima

Riferimento: 702/76

GRP blade holder, 22 mm blade throat

Recensioni: 0

This blade holder was specially developed for the large Bell 47 G III with a rotor diameter of 2.36 m. It has a 22 mm blade throat and a 6 mm Ø bore for the retaining screw, i.e. the matching blade holder screws and self-locking nuts are M6 in size.

Prezzo 37,80 €
Più
In vendita su richiesta
Rotor brake, GRP Anteprima

Riferimento: 72/4

Rotor brake, GRP

Recensioni: 0

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...

Prezzo 14,70 €
Più
In vendita su richiesta

Suivez-nous sur Facebook

Facebook