Panier de transport, 1 pièce

Référence: 341/402

Trappe kero Lama N1 1:4

dimensions: 4.3 x 2.5 cm, inner diameter: 1.43 cm

Référence: 134/444

Winch connections 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Référence: 341/507

Grand reservoir d'huile Lama 1:4

dimensions: 5.15 x 3.62 x 5.1 cm

Référence: 1/21

Casque pour Pilote William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Référence: 340/1

Support de roue pour Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Référence: 341/414

Lama 1: 4 luz anticolisión trasera

Référence: 340/29

Cockpit for Lama, turbine version

Référence: 341/421

Rueda de ventilador Lama 1: 4

Référence: 30/50

Extincteur, longueur env. 70 mm

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Référence: 341/417

Retroviseur grand Lama 1:4

dimensions: 4 x 5.4 x 1 cm

Référence: 330/2

Turbine factice GFK

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Référence: 340/40

Kit rétroviseurs pour grands modèles

Mirror set, complete as illustratede.g. for Lama and other large-scale modelsdimensions of the mirrors: approx. 40 x 84 and 14 x 22 mm

Référence: 341/419

Poulies de cables Lama x6 1:4

1,18 x 3,15 x 0,72 cmPack of 6

Référence: 341/420

Batterie Lama 1:4

dimensions: 3.2 x 5.25 x 7.75 cm

Référence: 341/416

Espejo Lama 1: 4

Référence: 330/5

Kit accessoires portes Bell 47 G III, Lama

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...