Panneau de cockpit détaillé pour Lama

Reference: 330/5

Fittings set Bell 47 G III, Lama

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Reference: 330/45

Hook for Lama

The hook for the Lama is fully functional. The scale aluminium frame comes with further more accessories, inclusive servo mount.The fuselage already offers the fastening, ready soldered.On your model you mount the hook in the required location, and release dummy loads by activating a servo via your transmitter.

Reference: 341/404

Position lights Lama x2 1:4

dimensions: 4.5 x 3.2 x 1.8 cmPack of 2 (l/r)

Reference: 341/412

Turbine air entry 1:4

dimensions: 8 x 3.5 x 4.3 cm

Reference: 134/444

Winch connections 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Reference: 350/17

Exhaust cover, Ø 90 mm

When the turbine of a full-size helicopter is not running, the engine is protected with an exhaust cover which prevents foreign objects finding their way inside the turbine. This exhaust cover for model turbines is suitable for the Lama, Alouette III and any other machine with a 90 mm Ø exhaust pipe. Caution: it is essential to allow the exhaust pipes to...

Reference: 341/409

BTP Lama 1: 4

Reference: 350/45

Working winch, fully functional

Great fascination is achieved by active working details on scale models, remember e.g. rotary lights and navigation lights.A working winch adds a special attraction on a model helicopter particularly if it is pivoting and fully functional!Especially on a Alouette III you hardly need fantasy, to see instead of the model the full-size helicopter in your...

Reference: 1/21

Helmet for pilot William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Reference: 341/402

Kerosene trap N1 1:4

dimensions: 4.3 x 2.5 cm, inner diameter: 1.43 cm

Reference: 341/36

Load basket

Load basket for Lamalength:410 mmwidth:100 mmheight70 mm

Reference: 340/5

Snowboards for Lama

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Reference: 341/407

Oil tank large Lama 1:4

dimensions: 6.5 x 4.5 x 6.,5 cm2-part

Reference: 340/6

Entry step, for Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Reference: 341/445

Pedales llama x2 1: 4

Reference: 341/420

Battery housing Lama 1:4

dimensions: 3.2 x 5.25 x 7.75 cm