Boitier électrique Lama 1:4

Riferimento: 340/6

Pedana di salita per Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Riferimento: 341/36

CESTELLO SOTTOPANCIA PER LAMA

Load basket for Lamalength:410 mmwidth:100 mmheight70 mm

Riferimento: 330/45

Gancio carico

The hook for the Lama is fully functional. The scale aluminium frame comes with further more accessories, inclusive servo mount.The fuselage already offers the fastening, ready soldered.On your model you mount the hook in the required location, and release dummy loads by activating a servo via your transmitter.

Riferimento: 340/5

Snowboards per Lama 1 paio

When full-size helicopters have to land in deep snow, the skids are fitted with "snowboards" to prevent them sinking in.On the model they look really good, and also help the pilot detect the model's orientation in the air.Make your model an eye-catcher and use some rivets for the decoration of the skies."Snowboards" for Lama, 1 pair

Riferimento: 341/429

Pannello Cockpit dettagliato, LAMA

Addition to the Cockpit Ord. No. 340/29 to make it look more realistic

Riferimento: 341/416

Espejo Lama 1: 4

Riferimento: 341/411

Llama estabilización trasera 1: 4

Riferimento: 134/460

Telephone on board 1:4

dimensions: 1.9 x 1.2 x 6.3 cm

Riferimento: 330/2

Imitazione turbina

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Riferimento: 340/1

Supporti ruota per Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Riferimento: 350/45

CESTELLO SOTTOPANCIA PER LAMA

Great fascination is achieved by active working details on scale models, remember e.g. rotary lights and navigation lights.A working winch adds a special attraction on a model helicopter particularly if it is pivoting and fully functional!Especially on a Alouette III you hardly need fantasy, to see instead of the model the full-size helicopter in your...

Riferimento: 341/418

Reinforcements for skis Lama 1:4

Riferimento: 341/412

Ingresso aria turbina Lama 1/4

dimensions: 8 x 3.5 x 4.3 cm

Riferimento: 341/413

Wiper, 1:4,2

dimensions: 10.63 x 0.7 x 1.3 cmPack of 2, each 2-part

Riferimento: 341/509

BTP Lama 1:5

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Riferimento: 350/17

Coperchio scarico Ø 90 mm

When the turbine of a full-size helicopter is not running, the engine is protected with an exhaust cover which prevents foreign objects finding their way inside the turbine. This exhaust cover for model turbines is suitable for the Lama, Alouette III and any other machine with a 90 mm Ø exhaust pipe. Caution: it is essential to allow the exhaust pipes to...