Motor mount for O.S and Webra P5 / P75 and Skyfox mechanics

Riferimento: 58/11

3 x 8 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 8 x 3 mmpack of...

Riferimento: 116/8

Silicone hose

The operating temperature of a tuned pipe or of a silencer has a destructive influence on their supports, if no heat resitant material is used when fixing.Silicone hose11 mm I.D.length approx. 300 mm

Riferimento: 870/49

Servo frame CFK

Riferimento: 64/32

pinion gear 23-tooth

Clutch pinion gearincl. flywheel and split taper collet23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor

Riferimento: 64/16

8 x 12 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 12 x 3.5 mmpack of...

Riferimento: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Riferimento: 72/31

Swivel bearing 8 x 16 x 8 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 8 x 16 x 8 mmpack of 1

Riferimento: 99 A

6 x 10 x 2.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 10 x 2.5 mmpack of...

Riferimento: 68/6

17 x 26 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness

Riferimento: 94/17

Thrust bearing 7 x 13 x 4.5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 7 x 13 x 4.5...

Riferimento: 16/3

Spray can holder

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Riferimento: 10/38

Penetrating oil

When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...

Riferimento: 68/51

Swivel bearing 12 x 22 x 10 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 12 x 22 x 10 mmpack of 1

Riferimento: 55/9

ball bearing 12 x 28 x 7 mm

Not available

Riferimento: 96/1

5 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 5 x 13 x 5 mmpack of...

Riferimento: 117/2

Thrust bearing 10 x 24 x 9 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 10 x 24 x 9...