Ball-link driver 4.0

Riferimento: 9/11

Three-armed gripper

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Riferimento: 11/26

Cizallas para paneles de acristalamiento

Riferimento: 11/84

Assembly spanner

If you want to extract the flywheel and the split tapper collet from the motor you hold the flywheel with the assembly spanner while you turn in the extractor screw.

Riferimento: 29/11

Widia disc cutter

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Riferimento: 11/28

Glasspaper file, flat

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Riferimento: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Riferimento: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Riferimento: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Riferimento: 11/64

Hole cutter up to 16 mm Ø

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Riferimento: 70/20

Die M 2.5 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Riferimento: 107/0

Ball-link driver with handle

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Riferimento: 11/60

Tubing cutter, up to 15 mm Ø

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Riferimento: 111/11

Handle for socket spanners Ø 6mm

Not available

Riferimento: 11/260

Glazing panel shears straight

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Riferimento: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Riferimento: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....