Soft sanding paper

Reference: 9/11

Three-armed gripper

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Reference: 11/86

Pushrod measuring holder

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Reference: 11/64

Hole cutter up to 16 mm Ø

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Reference: 10/77

Sanding sponge

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Reference: 11/53

Ridge cutter

Use this small ridge cutter to remove sharp burrs and edges from aluminium and plastics; e.g. remove sharp edges from an aluminium pipe.

Reference: 107/0

Ball-link driver with handle

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Reference: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Reference: 111/11

Handle for socket spanners Ø 6mm

Not available

Reference: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Reference: 107/2

Ball-link driver 4.0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Reference: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Reference: 11/44

Handle for socket spanners Ø 4mm

Accessories for the fine-point screwdriver set Ord.No. 11/39 are also available separately.

Reference: 11/26

Cizallas para paneles de acristalamiento

Reference: 11/260

Glazing panel shears straight

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Reference: 70/22

Die M 3.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Reference: 11/60

Tubing cutter, up to 15 mm Ø

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.