Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

RC-Vorbau Sky Fox

809/6
Valutazione 
44,30 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione
Der RC-Vorbau ist so konstruiert, daß er den Empfänger, den Akku und den Kreisel aufnimmt. Beim Tank wählen Sie Ord.No. 800/26 mit einem Fassungsvermögen von ca. 540 cm³.
Mit den beiliegenden M 3 x 8 Linsenschrauben verschrauben Sie die Einzelteile in den dafür vorgesehenen Inserts. Dann klippen Sie den Vorbau in die vorbereiteten Aufnahmen an den Sky Fox-Seitenteilen.
Von unten setzen Sie die schräg angeformte M 4 Verschraubung ein, um daran später die Kanzel des Modells mit einer M 4 Rändelschraube zu befestigen.
RC-Vorbau Sky Fox mit M 4 Verschraubung und 10 Linsenflanschschrauben M 3 x 8
Dettagli del prodotto
809/6
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

RC-Vorbau Sky Fox

RC-Vorbau Sky Fox

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Supporto per tubi... Anteprima

Riferimento: 310/8

Supporto per tubi sintonizzato in 2 parti

Recensioni: 0

GRP tuned pipe holders are used to secure the tuned pipe to the tail booms. They are easy to clamp in place. The tail pipe of the tuned pipe should be covered with silicone hose (Order No. 116/8), or with one of the tail pipes (Ord.No. 116/0 or 116/9), so that the heat of the pipe does not damage the holder.Tuned pipe holder, 2-partfor 20 mm ��tail boom

Prezzo 14,70 €
Più
In vendita su richiesta
Coda slitta rossa Anteprima

Riferimento: 800/20

Coda slitta rossa

Recensioni: 0

Tail skids only. Create your own individual colour scheme: e.g. white stabiliser - red skid!

Prezzo 5,50 €
Più
In vendita su richiesta
Stabilizzatore grande Anteprima

Riferimento: 800/25

Stabilizzatore grande

Recensioni: 0

If you fit a large stabiliser to your trainer there is no need for a tail skid. This stabiliser provides the tail rotor blades with enough ground clearance, and offers good flight stability at low airspeeds. There are two versions with different methods of attachment.275 mm high118 g total weightscrew fitting to tail rotor holder

Prezzo 30,60 €
Più
In vendita su richiesta
Stabilizzare 3-D, fibra di... Anteprima

Riferimento: 800/50

Stabilizzare 3-D, fibra di carbonio

Recensioni: 0

When you are attempting high-speed flying in reverse and also certain pirouettes you may find that the helicopter's heading changes due to the influence of the solid vertical stabiliser. That is the basic reason for the development of this special 3-D tail.It is very strong, and its large size removes the need for a tail skid. The stabiliser is...

Prezzo 62,80 €
Più
In vendita su richiesta
Stabilizzatore giallo Anteprima

Riferimento: 800/6

Stabilizzatore giallo

Recensioni: 0

Instead of a horizontal fin (for mounting on the tail boom) the small inset horizontal panel replaces that. The inset fits on top of the stabiliser, outwards opposite of the tail rotor.220 mm high, excl. tail skid3-part, 45 g total weight

Prezzo 27,40 €
Più
In vendita su richiesta

Seguici su Facebook

Facebook