Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Domplatte, Alu

860/53
Valutazione 
54,60 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione



Zur Alu-Domplatte wählen Sie das passende Kugellager je nach Einsatzort innerhalb des Modells X-Perience aus.

Dettagli del prodotto
860/53
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Domplatte, Alu

Domplatte, Alu

Scrivi la tua recensione
16 altri prodotti della stessa categoria:
Stabilizzatore grande Anteprima

Riferimento: 800/24

Stabilizzatore grande

Recensioni: 0

If you fit a large stabiliser to your trainer there is no need for a tail skid. This stabiliser provides the tail rotor blades with enough ground clearance, and offers good flight stability at low airspeeds. There are two versions with different methods of attachment.height 275 mm118 g total weightwith clamp for 20 mm Ø tail booms

Prezzo 30,60 €
Più
In vendita su richiesta
Supporto per tubi... Anteprima

Riferimento: 310/8

Supporto per tubi sintonizzato in 2 parti

Recensioni: 0

GRP tuned pipe holders are used to secure the tuned pipe to the tail booms. They are easy to clamp in place. The tail pipe of the tuned pipe should be covered with silicone hose (Order No. 116/8), or with one of the tail pipes (Ord.No. 116/0 or 116/9), so that the heat of the pipe does not damage the holder.Tuned pipe holder, 2-partfor 20 mm ��tail boom

Prezzo 14,70 €
Più
In vendita su richiesta
Supporto per tettuccio da... Anteprima

Riferimento: 800/37

Supporto per tettuccio da 26 mm

Recensioni: 0

The required length of the canopy holder is determined by the kind of canopy and the location of its fitting points on the side frames.

Prezzo 11,20 €
Più
In vendita su richiesta
Toothed belt, pitch T5/340 Anteprima

Riferimento: 870/105

Toothed belt, pitch T5/340

Recensioni: 0

Toothed belt, pitch 5for X-Treme trainer helicoptersWhen replacing a toothed belt please note that different toothed belts are used in X-Treme mechanics and X-Treme trainer helicopters.

Prezzo 37,50 €
Più
In vendita su richiesta
Stabilizzatore grande Anteprima

Riferimento: 800/25

Stabilizzatore grande

Recensioni: 0

If you fit a large stabiliser to your trainer there is no need for a tail skid. This stabiliser provides the tail rotor blades with enough ground clearance, and offers good flight stability at low airspeeds. There are two versions with different methods of attachment.275 mm high118 g total weightscrew fitting to tail rotor holder

Prezzo 30,60 €
Più
In vendita su richiesta

Seguici su Facebook