- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
Rotor brake, GRP, red
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Riferimento: 82/19
Bilanciere Delta, 200 mm
Aluminium rocker for Delta head, 5 mm ∅, alone.
Riferimento: 79
Flybar stainless steel 4 x 450 mm
The length of the flybar itself also plays an important role in the model's flight characteristics: the longer the flybar, the smoother the hover. A longer flybar increases the control deflections. 450 mm length is considered normal, while 510 mm provides more docile handling.
Riferimento: 832/73
Blade pivot shaft 10 x 187 mm
Blade pivot shaft 10 x 187 mm for rotor head 722/72
Riferimento: 76/19
GRP blade holder, 5 mm ∅ hole
As demands on helicopters continue to rise, so stronger blade holders are required. In this case a 14 mm blade holder is combined with a 5 mm Ø hole for blade retention, i.e. the matching blade holder screws and self-locking nuts are M5 in size.GRP blade holder with short linkage armfor multi-blade rotor heads
Riferimento: 703/45
Rotor head linkage for Alouette III
This rotor head linkage is essential for the correct operation of the rotor head of the Alouette III due to its heavy take-off weight.
Riferimento: 54/16
Clamp ring pitch compensator 17 mm
The 17 mm Ø clamp ring is fitted to the rotor head centre piece, the steel pin slides in the guide slot of the pitch compensator. Rotate the clamp for fine adjustment so that your helicopter flies straight when you apply a pitch-axis command.Clamp ring for pitch compensator 17 mm Ø, length of the pin 30 mm.
Riferimento: 71/26
Forcelle nylon trascinatore
Curved link Content of the package: 2 pieces
Riferimento: 72/4
Rotor brake, GRP
When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...
Riferimento: 707/5
Rotor head cover for 5-blade head
The multi-blade rotor heads of full-size helicopters are generally fitted with protective covers; this applies to the Ecureuil, the Dauphin, the Eurocopter EC 135 and 145, the MD Hughes, etc. Rotor head covers also look good on your model, and we stock them with indentations corresponding to the number of blade grips. The covers are made of CFRP and can...
Riferimento: 74/6
O-ring 2 x 6 mm soft
O-ring 2 x 6 mm soft Content of the package: 8 piecesTip: O-rings always slide with a drop of silicone oil onto the shaft.
Riferimento: 702/76
GRP blade holder, 22 mm blade throat
This blade holder was specially developed for the large Bell 47 G III with a rotor diameter of 2.36 m. It has a 22 mm blade throat and a 6 mm Ø bore for the retaining screw, i.e. the matching blade holder screws and self-locking nuts are M6 in size.
Riferimento: 722/71
Collective pitch compensator 12 mm
Pitch compensator, complete, for 12 mm Ø main shaft, centre piece aluminium.For use with the rotor head Ord.No. 722/72.
Riferimento: 480/53
Co-rotating dome coverage-set
You can fit to your Chinook heads a plate each that covers the dome and spins with the rotor head rpm. A pretty detail, that also can be found on the original Chinook helicopters. The plates / dome covers are mounted on the clamp rings of the main shafts.Pack of 2 plates incl. mounting material