Rocker kit for Bell UH / Bell 212 T-Rex

Référence: 68/22

Aluminium side frames

Aluminium side frames for swashplate driver 68/20 and 68/50. Content of the package: 2 pieces

Référence: 704/31

4-blade centre piece, 10 mm

Item to a multi-blade rotor head for Ø 10 mm shaft; see Ord.No. 703/30, 704/30 and 705/30.

Référence: 87/4

Chape double 90°

A 90° twisted double ball-link connect the mixer lever to the ball collet on the flybar. Content of the package: 2 pieces

Référence: 71/18

Spacer for pitch compensator 2.8 x 5 x 2 mm

 Content of the package2 pieces

Référence: 82/23

Washer for Delta rocker 5 mm

Washer for Delta rocker 5 mm Content of the package: 2 pieces

Référence: 76/25

Blade holder, blade grip 18 mm

Not available

Référence: 707/5

Rotor head cover for 5-blade head

The multi-blade rotor heads of full-size helicopters are generally fitted with protective covers; this applies to the Ecureuil, the Dauphin, the Eurocopter EC 135 and 145, the MD Hughes, etc. Rotor head covers also look good on your model, and we stock them with indentations corresponding to the number of blade grips. The covers are made of CFRP and can...

Référence: 72/42

CFRP plates for aluminium hub

This rotor head hub with its bonded-in carbon fibre plates is a real head-turner. The plates are simply glued into the existing recesses on both sides. We recommend silicone rubber, Ord.No. 10/11, as adhesive.CFRP plates for aluminium hub matching Ord.No. 832/72pack quantity: 2 plates

Référence: 78/45

Mixer lever set, aluminium

These mixer levers from aluminium are particularly torsion proof and feature an improved control precision. For individual settings you can change the connection of the linkage (relocate the balls).Flanged bearings 3 x 7 x 3 mm are suitable also, i.e. you use existing ballraces again.Place of installation: all rotor heads which are provided with the...

Référence: 74/19

Joint torique, souple 1.5 x 19 mm

O-ring 1.5 x 19 mm soft Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Référence: 72/3

Rotor brake, GRP, red

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...

Référence: 74/4

O-ring 2 x 4 mm soft

O-ring 2 x 4 mm soft Content of the package: 8 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Référence: 78/41

Mixer lever cranked

Mixer lever, content of the package 1 piece.Additionial accessories for the use of mixer levers are either two flanged ballraces or two flanged bushes from Delrin as a low cost alternative. The screwing on the blade holder arm complies with the kind of hole, i.e. it depends on the through hole or on the blind hole. Please note for choosing the screws:...

Référence: 71/4

Pièce centrale en alu Ø 10 mm

Pitch mixer centre piece, aluminium, 10 mm ∅

Référence: 1005/8

Kit de conversión varillaje directo para JetRanger XL eléctrico

Référence: 72/50

Electro rotor head centre piece

Electro rotor head centre piece, alu.