3-Blatt-Rotorkopf 12 mm

Reference: 706/20

6-Blatt Rotorkopf für Ø 12 mm Welle

Reference: 705/37

5-blade rotor head 12 mm

Not available

Reference: 705/35

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 702/75

Semi scale rotor head

With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....

Reference: 703/34

3 blade rotor head, 12 mm

Not available

Reference: 722/75

Conversion set for rotor head without flybar

This conversion set was originally developed for the Robinson R22 and Jet Ranger, but since then it has proved to be useful for a number of other large-scale models.Please note that the matching...

Reference: 1005/47

Bell 47 G rotor head

This rotor head was modelled as closely as possible on the original version installed on the Bell 47 G full-size helicopter. It is an excellent choice for use on the Bell 47 G III model, Ord. No. 4700.The centrifugal weights and springs are dummies, and do not work. The rotor blade swivel limits are also imitations, and have no function.The blade grips...

Reference: 722/72

Rotor head VR-22

The loading of every component of this rotor system is designed to take a multiple of the actual forces. We are looking here at purely safety reserves and under no cirumstances should they be used for experimental purposes.Because of the special requirements of materials used in the rotor head, we expressly recommend that only genuine VARIO spare parts...

Reference: 704/30

4-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/30

3-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 268/72

3-blade rotor head for 15 mm rotor shaft

3-blade rotor head for 15 mm Ø rotor shaft.

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/38

3-blade rotor head 12 mm

Not available

Reference: 702/80

Semi scale rotor head SKS

The UH-1D or UH-1B models with an excessive length of the rotor shaft out of the mechanics fly for safety reasons with rotor shafts of 12 mm Ø. The difference between the SKS semi-scale rotor heads on offer is due to the centre hub. This version fits the shaft diameter of 12 mm.We recommend this rotor head for experenced pilots only.The performance of...

Reference: 702/70

Semi scale rotor head

This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...

Reference: 1005/60

Rotor head petrol mechanics 10 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...