Testa del rotore a 4 pale 10 mm

Reference: 703/30

3-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/60

Rotor head petrol mechanics 10 mm

Because of the high established demand on a rotor head being used in a mechanics driven by a petrol engine, the equipment is quite different from other rotor heads.Here flybars with 5 mm Ø are used, and the ball collets, the control bridge and the ballraces are applicable for this dimension. The aluminium centre piece accounts for the necessary precision...

Reference: 702/75

Semi scale rotor head

With the SKS semi-scale rotor head you will take the advantage of a mechanical gyro system with a delay in control commands caused by the flybar level.This system suits the scale looks of a UH-1D....

Reference: 704/36

4-blade rotor head 12 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/34

3 blade rotor head, 12 mm

Not available

Reference: 1005/59

Rotorkopf für TurbineOrd.No. 1005/59

Reference: 1005/12

Rotor head for Bell 212Ord.No. 1005/12

The basic method of operation of the turbine-powered Bell 212's rotor head is the same as that of the Bell 47 G III rotor head. The main difference is that the components have been modified to match the appearance of the Bell 212, and are therefore of different design. For example, a separate swashplate driver is not required, as it is integrated into the...

Reference: 704/35

4-blade rotor head, 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 1005/50

Sky Fox rotor head

The Sky Fox rotor head in its original form is robust and very sturdy, so it can achieve good results in all flight positions.The rotor head is supplied with a ball raced pitch compensator and two main shaft collars, their use depends on the length of the rotor shaft.CautionIt is not permissible to use this rotor head on a mechanical system powered by a...

Reference: 702/59

2-Blade-Rigid-Rotor head for 10 mm / ø4 mm

Not available

Reference: 702/70

Semi scale rotor head

This semi-scale rotor head includes additional mixing of the blade holder actuator linkage at a ratio of 2 : 1. This results in well-balanced flying characteristics, and the model has a damped rather than direct response to your control inputs (resembling a 2-blade head with flybar).Use only the suggested rotor blades for flybar-less rotor heads,...

Reference: 703/39

Scale rotor head for Vario Lama

Lama Scale Rotorhead: for the large Vario LamaWe have now finalized our tests with the Starwood Lama scale rotorhead on the Vario Lama 1:4. Now we are proud to present to you under the Ord.No. 703/39, a truly Scale rotor head including all necessary parts in order to mount this head on the Vario Lama.The head is available now. The kit includes the...

Reference: 704/37

4-blade rotor head 12 mm

Not available

Reference: 705/30

5-blade rotor head 10 mm

Rotor heads with three or more rotor blades really deserve their own chapter in any discussion of model helicopters; speculation is always in the air at such times, because sooner or later most...

Reference: 703/43

3-blade rotor head for 12 mm, from 20 kg

The take-off weight of our large Alouette III is relatively high, and we therefore decided to revise the linkage for the XL-C rotor head and the 3-blade rotor head in order to optimise the system...

Reference: 702/80

Semi scale rotor head SKS

The UH-1D or UH-1B models with an excessive length of the rotor shaft out of the mechanics fly for safety reasons with rotor shafts of 12 mm Ø. The difference between the SKS semi-scale rotor heads on offer is due to the centre hub. This version fits the shaft diameter of 12 mm.We recommend this rotor head for experenced pilots only.The performance of...