- Es gibt keine Artikel mehr in Ihrem Warenkorb
- Versand kostenlos
- Gesamt 0,00 €
- Helikoptermodelle
- Trainer / Zweckhelikopter
- Mechaniken und Zubehör
- Scale-Ausbau
- Nieten
- Innenausbau
- Außenanbauteile
- Mehrblatt-Sätze
- Modellspezifisch
- Agusta AW 139 1:7
- AIRWOLF 2001 1:8
- AIRWOLF 2002/2003 1:7
- AIRWOLF 2004 1:5
- Apache 1:7
- neue 3D-Scaleartikel
- Bell 230/430 1:7
- Bell 412 1:6
- Bell 429 1:5
- Bell UH / 212 / 412 1:5
- Bell UH / 212 / 412 1:7
- EC 120
- EC 135/145 1:4
- EC 135/145 1:6
- Ecureuil 1:4
- Ecureuil 1:6
- Gazelle
- H145 T2
- JetRanger XL
- sonstige Aussenanbauten
- Lama / Alouette II 1:4
- Lama 1:5
- Lama / Alouette II 1:6
- Antrieb und Zubehör
- Transmision/Engranajes
- Rotorköpfe und Zubehör
- Heckrotor
- Rotorblätter
- Werkzeug, Klebstoffe
- Rumpfeinzelteile
- Elektronik
- Kleb- u. Schmierstoffe
- Kugellager$ Befestigung
- Fanartikel$ Nützliches
- Flugfertige Modelle ((A)RTF)
- Fundgrube
- KATALOG
- Earthmovers
- Angebote
- Neue Artikel
- Modelado 3D
Keine Marke
Articulated centre support
Política de seguridad
Política de envío
Política de devolución
Aktuell keine Kunden-Kommentare
Riferimento: 603/18
Adaptor 20/33, Schweizer 300 C
Component part for fuselages, Ord.No. 6030 or 6031.
Riferimento: 603/17
Adaptor 20/33, Schweizer 300 C
Component part for fuselages, Ord.No. 6030 or 6031.
Riferimento: 17/16
Stainless steel tube 6.0 x 0.3 x 950 mm
Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm
Riferimento: 105/14
Stainless steel tube 8.0 mm, 2-part for Jet Ranger
Stainless steel tube 8.0 mm2-part (462 mm + 1160 mm)
Riferimento: 17/9
Centre bearing for lattice fuselage
Centre bearing for lattice fuselage Alouette II and Bell 47
Riferimento: 17/15
Stainless steel tube 6 x 890 mm
Stainless steel tube 6.0 x 0.3 x 890 mm
Riferimento: 17/14
Stainless steel tail drive system for 20 mm
Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...
Riferimento: 17/55
Stainless steel tail drive system for 40° gear
Stainless steel drive for installationin models with 40° angle gearboxcomplete as shown
Riferimento: 17/10
Stainless steel tail drive system
When a 2 mm steel drive wire is used between main gearbox and tail gearbox the tail rotor might yaw the heli during acrobatics (e.g. turn), because the wire might "wind up". At this moment a small "wind up" will cause a small change of tail rpm, which requires steering corrections.A so-called "rigid" tail drive system gives a more exact drive to the tail...
Riferimento: 17/13
Articulated joint tail drive system
On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support
Riferimento: 17
Tail rotor shaft 2 mm
The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm
Riferimento: 17/8
Connecting plug for tube 8 mm
Connecting plug for stainless steel tube 8 mm pack of 2
Riferimento: 17/18
Connecting plug for tube 5 mm
Connecting plug for stainless steel tube 5 mm pack of 2
Riferimento: 17/20
Stainless steel tail drive system
This version of the ballraced tail rotor drive system is designed for installation in full-fuselage models. Power is transmitted by a 6 mm stainless steel drive shaft with a length of 980 mm.This length ensures that the system can be used in virtually all our larger fuselages, provided that the main and tail rotors are fitted with the articulated...
Riferimento: 945/14
Stainless steel tail drive shaft ø 8 x 986 mm for Hughes Logo
Not available