Marchi

Nessuna marca

Fornitori

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 12,80 €
Più
In vendita su richiesta
Tutte le migliori vendite

Stainless steel tail drive system

17/20
Valutazione 

This version of the ballraced tail rotor drive system is designed for installation in full-fuselage models. Power is transmitted by a 6 mm stainless steel drive shaft with a length of 980 mm.

This length ensures that the system can be used in virtually all our larger fuselages, provided that the main and tail rotors are fitted with the articulated connections 49/56 and 49/60.

114,50 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

This version of the ballraced tail rotor drive system is designed for installation in full-fuselage models. Power is transmitted by a 6 mm stainless steel drive shaft with a length of 980 mm.

This length ensures that the system can be used in virtually all our larger fuselages, provided that the main and tail rotors are fitted with the articulated connections 49/56 and 49/60.

Dettagli del prodotto
17/20
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Stainless steel tail drive system

Stainless steel tail drive system

This version of the ballraced tail rotor drive system is designed for installation in full-fuselage models. Power is transmitted by a 6 mm stainless steel drive shaft with a length of 980 mm.

This length ensures that the system can be used in virtually all our larger fuselages, provided that the main and tail rotors are fitted with the articulated connections 49/56 and 49/60.

Scrivi la tua recensione
16 other products in the same category:

Reference: 17

Tail rotor shaft 2 mm

Review(s): 0

The 2 mm steel tail rotor shaft has proved its worth for several decades, especially in beginners' models.Drive shaft, steel, 2.0 x 980 mm

Price 6.60€
More
On sale upon request

Reference: 17/7

Articulated centre support

Review(s): 0

The use of an articulated centre support in helicopters with extreme high mounted tail booms (e.g. Hughes 500) helps to balance up to 30 mm vertical off-set between mechanics and tail rotor. The centre support is double ballraced and pre-assembled.

Price 75.80€
More
On sale upon request

Reference: 17/13

Articulated joint tail drive system

Review(s): 0

On a model helicopter like the Hughes 500 e.g. the tail boom is extremely high connected. Therefore an articulated centre support is applied in addition to the articulated tail drive system. The centre support is double ballraced and pre-assembled.Articulated joint tail drive systemwith articulated centre support

Price 153.40€
More
On sale upon request

Reference: 17/14

Stainless steel tail drive system for 20 mm

Review(s): 0

Of course the explanation of Ord.No. 17/10 concerning a 2 mm steel drive wire in acrobatics applies not only for fuselages, it is similar for training helicopters.When you convert a trainer you use the existing tail boom. Main gearbox and tail gearbox have to be provided with a claw connector 49/12 each.Models over a certain age should be checked whether...

Price 94.20€
More
On sale upon request

Reference: 17/16

Stainless steel tube 6.0 x 0.3 x 950 mm

Review(s): 0

Advanced pilots appreciate the more precise control response of a rigid tail rotor drive system, as provided by a stainless steel drive shaft. Stainless steel tube 6.0 x 0.3 x 950 mm

Price 36.50€
More
On sale upon request

Reference: 17/10

Stainless steel tail drive system

Review(s): 0

When a 2 mm steel drive wire is used between main gearbox and tail gearbox the tail rotor might yaw the heli during acrobatics (e.g. turn), because the wire might "wind up". At this moment a small "wind up" will cause a small change of tail rpm, which requires steering corrections.A so-called "rigid" tail drive system gives a more exact drive to the tail...

Price 75.80€
More
On sale upon request

Reference: 800/9

PTFE bush guide for 0.8 mm tailboom

Review(s): 0

PTFE guides in the tail boom provide the necessary "lubrication" for the drive shaft, which eliminates the need to oil the system separately.PTFE guide for 0.8 mm tail boomPack of 3 

Price 19.90€
More
On sale upon request

Seguici su Facebook