O-ring 9 x 4.5 mm

Riferimento: 68/19

Bearing pin

Bearing pin for swashplate driver 68/20. Content of the package: 1 piece.

Riferimento: 480/53

Co-rotating dome coverage-set

You can fit to your Chinook heads a plate each that covers the dome and spins with the rotor head rpm. A pretty detail, that also can be found on the original Chinook helicopters. The plates / dome covers are mounted on the clamp rings of the main shafts.Pack of 2 plates incl. mounting material

Riferimento: 72/5

Rotor brake, GRP

When you have landed and stopped the engine, the rotor head continues spinning for quite some time until it stops by itself. A rotor brake shortens the time you have to wait. Using light pressure with the flat of your hand on the domed face of the rotor brake you can stop the rotor in a few moments.Please note: stay in safe distance away from the turning...

Riferimento: 71/56

Corpo centrale per 12 mm, alluminio

Pitch mixer centre piece, aluminium, 12 mm Ø

Riferimento: 703/72

Eje de rodamiento de cuchillas para cabezal de 3 cuchillas

Riferimento: 79/8

Inertia weights for Ø 5 mm flybar

Inertia weights are small "extra brakes". They increase the gyroscopic stability of the flybar and slow down the rotor head's response. For every beginner we recommend these so the responsiveness of the rotor head is reduced. The rotor head becomes more responsive as the inertia weights are moveded inwards (always place equally!). Inertia weights suitable...

Riferimento: 54/18

Clamp ring for 12 mm

Same design as clamp ring 54/13, but for 12 mm Ø main rotor shaft.Clamp ring for pitch compensator 12 mm Ø, length of the pin 40 mm.

Riferimento: 82/23

Washer for Delta rocker 5 mm

Washer for Delta rocker 5 mm Content of the package: 2 pieces

Riferimento: 702/97

Linkage ball

Not available

Riferimento: 74/7

Rotor head dampers for 2 blade FBL systems

Flybarless electronics have now become common. Where they are being used harder damping is required.For these cases Vario is now offering a harder damping of the blade shaft provided by a pretension absorbing element in the centre block.For the adjustment, the outer O-ring position can be selected between "hard" and "soft" flight characteristics.Important...

Riferimento: 54/16

Clamp ring pitch compensator 17 mm

The 17 mm Ø clamp ring is fitted to the rotor head centre piece, the steel pin slides in the guide slot of the pitch compensator. Rotate the clamp for fine adjustment so that your helicopter flies straight when you apply a pitch-axis command.Clamp ring for pitch compensator 17 mm Ø, length of the pin 30 mm.

Riferimento: 74/15

Anello 2,5 x 12 mm. per Elastomero

Pack of 4Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Riferimento: 707

Rotor cap for Multi blade head

The diameter is 83 mm and the construction height from the screw-on surface to the highest point is 13 mm.It is fastened using an M4 x 14 hexagon socket screw (included).

Riferimento: 72/18

Rotor head centre piece, rigid

Aluminium centre piece, rigid, for 10 mm main shaft

Riferimento: 91/50

Paletti 105 x 60 mm per Ø 4+ 5 mm

Paddles1 pairapprox. 29 g eachfor ∅ 4 mm / 5 mm flybar

Riferimento: 82/9

Aluminium rocker

When you use a speed regulator you put the magnets into the cut-outs of this clamp ring. Clamp ring for speed collection, 10 mm Ø.