Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Tubo de PVC 3.2 x 2.2 x 1000 mm, wh

18
Valoración 
Tubo de PVC de 3,2 x 2,2 x 1000 mm, WH
3,10 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Tubo de PVC de 3,2 x 2,2 x 1000 mm, WH
Detalles del producto
18
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Tubo de PVC 3.2 x 2.2 x 1000 mm, wh

Tubo de PVC 3.2 x 2.2 x 1000 mm, wh

Tubo de PVC de 3,2 x 2,2 x 1000 mm, WH
Escriba su propia reseña
16 other products in the same category:

Reference: 3942

Servo packer

Review(s): 0

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Price 5.60€
More
On sale upon request

Reference: 13/21

Magnets for speed regulator

Review(s): 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Price 9.50€
More
On sale upon request

Reference: 3935/4

Servo extension lead 700 mm

Review(s): 0

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Price 8.90€
More
On sale upon request

Reference: 33/28

Rotor blade tie-down

Review(s): 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Price 22.10€
More
On sale upon request

Reference: 18/10

PTFE tube for tail drive shaft

Review(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Price 11.50€
More
On sale upon request

Reference: 8/3

Tail rotor flange

Review(s): 0

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Price 8.30€
More
On sale upon request

Reference: 74

O-ring 3 x 8 mm hard

Review(s): 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Price 3.90€
More
On sale upon request