Tanque de aceite (largo) Lama 1:5

Reference: 134/444

Winch connections 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Reference: 341/418

Reinforcements for skis Lama 1:4

Reference: 330/45

Hook for Lama

The hook for the Lama is fully functional. The scale aluminium frame comes with further more accessories, inclusive servo mount.The fuselage already offers the fastening, ready soldered.On your model you mount the hook in the required location, and release dummy loads by activating a servo via your transmitter.

Reference: 330/10

Cabin sheath for Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Reference: 341/509

Lama BTP 1:5

dimensions: main part: 9.5 x 4.95 x 6.4 cm6-part

Reference: 350/45

Working winch, fully functional

Great fascination is achieved by active working details on scale models, remember e.g. rotary lights and navigation lights.A working winch adds a special attraction on a model helicopter particularly if it is pivoting and fully functional!Especially on a Alouette III you hardly need fantasy, to see instead of the model the full-size helicopter in your...

Reference: 340/6

Entry step, for Lama

If you have a mind to continue adding detail fittings to your Lama, you are sure to appreciate this landing gear step which can be fitted to an existing model at any time. The step is made of stainless steel, and is supplied complete with clips, screw fittings and tread material. Entry step, for Lama, pack of 1

Reference: 341/413

Wiper, 1:4,2

dimensions: 10.63 x 0.7 x 1.3 cmPack of 2, each 2-part

Reference: 341/520

Battery housing /Lama

dimensions: 7.76 x 3.4 x 5.3 cm

Reference: 340/13

Dummy power unit

This dummy power unit can be installed on turbine powered helicopters to produce an even more realistic intersection between the turbine and the gearbox.When the imitation rotor brake of the dummy part is pushed over the turbine starter, the rubber connector is spring-loaded in front of the gearbox connection; retaining screws are not required.Dummy power...

Reference: 1/21

Helmet for pilot William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Reference: 341/429

Detailed Cockpit panel, Lama

Addition to the Cockpit Ord. No. 340/29 to make it look more realistic

Reference: 330/36

Door latch for Lama

If you don't want that the doors of the Lama canopy close itself after opening, you use these magnet latches.

Reference: 340/40

Mirror set for large-scale models

Mirror set, complete as illustratede.g. for Lama and other large-scale modelsdimensions of the mirrors: approx. 40 x 84 and 14 x 22 mm

Reference: 341/421

Rueda de ventilador Lama 1: 4

Reference: 330/31

Bubble window for Lama

Bubble window for Lama Ord.No. 3300 / 3400 / 3401, Rotor ø 2500 mm