Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Servo Laterals CFRP, X-Treme

870/49
Valoración 
Lado Servo frames CFRP, X-Treme
51,70 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Lado Servo frames CFRP, X-Treme
Detalles del producto
870/49
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Servo Laterals CFRP, X-Treme

Servo Laterals CFRP, X-Treme

Lado Servo frames CFRP, X-Treme
Escriba su propia reseña
16 autres produits dans la même catégorie :

Référence: 71/16

3 x 7 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 7 x 3 mmpack of...

Prix 9,40 €
Détails
En vente sur demande

Référence: 75

8 x 16 x 4 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 16 x 4 mmpack of...

Prix 9,90 €
Détails
En vente sur demande

Référence: 10/38

Penetrating oil

Commentaire(s): 0

When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...

Prix 13,40 €
Détails
En vente sur demande

Référence: 39/2

10 x 22 x 6 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 22 x 6 mmpack of...

Prix 12,80 €
Détails
En vente sur demande

Référence: 117/8

Thrust bearing 8 x 15 x 5 mm

Commentaire(s): 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 8 x 15 x 5...

Prix 12,70 €
Détails
En vente sur demande

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 11,30 €
Détails
En vente sur demande

Référence: 7/37

8 x 16 x 6 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 16 x 6 mmpack of...

Prix 11,60 €
Détails
En vente sur demande

Référence: 68/1

Swivel bearing 10 x 19 x 9 mm

Commentaire(s): 0

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 10 x 19 x 9 mmpack of 1

Prix 22,10 €
Détails
En vente sur demande

Référence: 99 A

6 x 10 x 2.5 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 10 x 2.5 mmpack of...

Prix 9,40 €
Détails
En vente sur demande

Référence: 117/2

Thrust bearing 10 x 24 x 9 mm

Commentaire(s): 0

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 10 x 24 x 9...

Prix 22,10 €
Détails
En vente sur demande

Référence: 17/24

8 x 14 x 4 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 14 x 4 mmpack of...

Prix 11,90 €
Détails
En vente sur demande