Accueil
Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 83 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 25-36 de 83 article(s)

Filtres actifs

Crankshaft nut socket... Aperçu rapide

Référence: 11/67

Crankshaft nut socket spanner 14 mm

Commentaire(s): 0

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Prix 23,90 €
Détails
En vente sur demande
Magnetiser Aperçu rapide

Référence: 11/22

Magnetiser

Commentaire(s): 0

Everyone has experienced the annoyance of small screws which won't stay on the screwdriver. This magnetiser solves the problem. It is a small, handy unit which will magnetise any screwdriver, and the screw will then stick to it. You simply place the screwdriver in the "+" socket and move it to and from. To de-magnetise it repeat the procedure in the "-"...

Prix 18,30 €
Détails
En vente sur demande
Assembly tray, 25-part Aperçu rapide

Référence: 90/9

Assembly tray, 25-part

Commentaire(s): 0

Appropriate precautions should always be taken every time you start working on your model, and one of them is to prepare a suitable temporary storage area for small and ultra-small components. These assembly trays are sub-divided into small compartments, allowing you to sort components according to the stage of construction, while a second tray is used to...

Prix 18,40 €
Détails
En vente sur demande
Spray can holder Aperçu rapide

Référence: 16/3

Spray can holder

Commentaire(s): 0

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Prix 11,90 €
Détails
En vente sur demande
Five minute epoxy, 50 ml Aperçu rapide

Référence: 10/73

Five minute epoxy, 50 ml

Commentaire(s): 0

The more you build, the more frequently you use epoxies, whose components must be proportionately mixed. When you insert cartridges into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use. Pack of 50 ml, pot life approx. 5 minutes

Prix 18,60 €
Détails
En vente sur demande
Penetrating oil Aperçu rapide

Référence: 10/38

Penetrating oil

Commentaire(s): 0

When flying in moist air or rainy conditions you may find that rust starts to form on shafts. If this happens you could find that the swashplate is stuck fast the following day. A quick spray of penetrating oil will prevent oxidation getting a hold on the swashplate. Use it on the main rotor shaft and tail rotor shaft after flying; a few little squirts...

Prix 13,40 €
Détails
En vente sur demande
6 x 13 x 5 mm Aperçu rapide

Référence: 17/22

6 x 13 x 5 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 13 x 5 mmpack of...

Prix 11,20 €
Détails
En vente sur demande
7 x 14 x 3.5 mm Aperçu rapide

Référence: 17/23

7 x 14 x 3.5 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 7 x 14 x 3.5 mmpack of...

Prix 11,20 €
Détails
En vente sur demande
3 x 7 x 3 mm Aperçu rapide

Référence: 71/16

3 x 7 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 7 x 3 mmpack of...

Prix 13,50 €
Détails
En vente sur demande
6 x 10 x 2.5 mm Aperçu rapide

Référence: 99 A

6 x 10 x 2.5 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 10 x 2.5 mmpack of...

Prix 13,50 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook