Accueil

Filtrer par

Disponibilité

Disponibilité

Prix

Prix

  • 5,00 € - 131,00 €

Catégories

Catégories

Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 44 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 25-36 de 44 article(s)

Filtres actifs

  • Catégories : Accessoires spécifiques
  • Catégories : Clefs
  • Catégories : Gabarits
Tubing cutter, up to 15 mm Ø Aperçu rapide

Référence: 11/60

Tubing cutter, up to 15 mm Ø

Commentaire(s): 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Prix 33,30 €
Détails
En vente sur demande
Hole cutter up to 16 mm Ø Aperçu rapide

Référence: 11/64

Hole cutter up to 16 mm Ø

Commentaire(s): 0

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Prix 54,60 €
Détails
En vente sur demande
Pipe bending tool Aperçu rapide

Référence: 11/80

Pipe bending tool

Commentaire(s): 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Prix 44,30 €
Détails
En vente sur demande
Pushrod measuring holder Aperçu rapide

Référence: 11/86

Pushrod measuring holder

Commentaire(s): 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prix 14,80 €
Détails
En vente sur demande
Three-armed gripper Aperçu rapide

Référence: 9/11

Three-armed gripper

Commentaire(s): 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Prix 11,70 €
Détails
En vente sur demande
Die M 2.5 HSS Aperçu rapide

Référence: 70/20

Die M 2.5 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 46,10 €
Détails
En vente sur demande
Die M 2.0 HSS Aperçu rapide

Référence: 70/21

Die M 2.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 54,60 €
Détails
En vente sur demande
Die M 3.0 HSS Aperçu rapide

Référence: 70/22

Die M 3.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 37,80 €
Détails
En vente sur demande
Protective goggles Aperçu rapide

Référence: 9/5

Protective goggles

Commentaire(s): 0

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Prix 14,80 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook