Rotor blade pouch 5-blade Ø 2500 mm

Référence: 18/9

PVC tube 4.5 x 3.3 x 380 mm, white

PVC tube 4.5 x 3.3 x 380 mm, white

Référence: 97/9

Screw fitting pushrod connector

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Référence: 18/1

PVC tube 3.0 x 2.0 x 980 mm, red

PVC tube 3.0 x 2.0 x 980 mm, red

Référence: 33/1

Rotor blade pouch 2-blade Ø 2500 mm

bag length: 120 cmmax. blade width: 9.5 cm

Référence: 890/25

Cooling fan support for Schweizer 300 C

Component part for fuselage, Ord.No. 6030 or 6031.

Référence: 1414

Battery Switch

Dual power supply with gas cap switch

Référence: 3942

Servo packer

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Référence: 17/2

Steel guide 6.2 x 10 mm

Content of the package 1 piece

Référence: 8/3

Tail rotor flange

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Référence: 33/5

Rotorblatttasche 5-Blatt max Ø 2500 mm

Référence: 18/10

PTFE tube for tail drive shaft

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Référence: 10/75

Glue dispenser

When you insert cartridges Ord.No. 10/73 into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use.

Référence: 791/28

Wing brace

The wing brace prevents the wings vibrating; it can be installed in the Cobra, depending on model version.

Référence: 3941/90

Servo mounting set

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Référence: 3948

Servo numbers

Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30

Référence: 3944

Servo mount 120°

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...