Hook-and-loop tape 30 x 500 mm

Référence: 755/26

Foam rubber sleeve

Batteries, receiver etc. are very safe in the front structure if they are packed in a foam sleeve.Many hard landings will cause no damage. The same applies to your electronic units provided that they are cossetted in a shock-absorbing foam sleeve.You just cut off the length you require.Inner diameter: 35 mmFoam rubber sleeve, approx. 250 mm

Référence: 1409

cable clamp

The cable holder can be fixed over the eyelet. then wrap the sheathed metal strap around the cable.Length: 32 mmPack of 10

Référence: 809/2

Gyro/receiver plate

A good method of mounting your gyro or your receiver is to use this aluminium plate.

Référence: 755/25

Foam tube

Thickness:9 mmInside Ø:22 mmLength:250 mm

Référence: 3504

Cable and tube fittings

These clips can be used for cables and tubing, and help to deploy all such items neatly inside your models. The set contents are designed to meet the needs of the typical turbine-powered helicopter. Tidily arranged leads make a considerable contribution to operational safety in your valuable model! Set complete as illustrated.

Référence: 28/17

Banana plugs

Banana plugs red and black Pack of 2

Référence: 1407

Cable spiral tubing

Cables which could chafe somewhere on the model are best run in this flexible spiral tubing – it keeps the cables well protected. It doesn't matter whether there are two or six servo cables, the cable spiral tubing expands round the cables keeping the installation neat. Each pack has 1 m length. black

Référence: 742/38

Doppelseitiges Klebeband 19 mm

Référence: 1408

Textile cable protection sleeve

A practical method of protecting cables in any model helicopter. This textile-reinforced sleeve protects cables very effectively when they have to be bundled together inside the mechanics; typically servo and extension leads.Length: 1 m

Référence: 25/9

Heat reflective mat

Between fuselage and exhaust tube a heat-reflecting mat avoids melting of the fibreglass. Even in smaller fuselages where conventional silencer systems are close to the inside surface, the heat reflective mat is useful as a heat shield.Heat reflective matheat rejectingsize approx. 300 x 700 mmmat thickness approx. 3 mm

Référence: 3503

RC connector retainer

Extension cable plugs should not loosen themselves or even come apart. The safety clip for RC-plug connections guarantees permanent contact. Pack of 2

Référence: 742/35

Cable tie 100 mm black

Cable ties have a versatile use: they fasten fuel pipes in the right position, they fasten your training undercarriage to the skids, they tidy cables and they even hold fuel tanks and batteries. Contents of each pack 10 pieces available in different length 100 mm black 100 mm white 200 mm black 200 mm white 360 mm black

Référence: 1406

Cable spiral tubing

Cables which could chafe somewhere on the model are best run in this flexible spiral tubing – it keeps the cables well protected. It doesn't matter whether there are two or six servo cables, the cable spiral tubing expands round the cables keeping the installation neat. Each pack has 1 m length. transparent

Référence: 742/42

Cable tie 360 mm black

Cable ties have a versatile use: they fasten fuel pipes in the right position, they fasten your training undercarriage to the skids, they tidy cables and they even hold fuel tanks and batteries. Contents of each pack 10 pieces available in different length 100 mm black 100 mm white 200 mm black 200 mm white 360 mm black

Référence: 742/41

Cable tie 200 mm white

Cable ties have a versatile use: they fasten fuel pipes in the right position, they fasten your training undercarriage to the skids, they tidy cables and they even hold fuel tanks and batteries. Contents of each pack 10 pieces available in different length 100 mm black 100 mm white 200 mm black 200 mm white 360 mm black

Référence: 755/29

Elastic velcro for battery attachment

length: 30 cmPack of 2