Kit manches à balai

Reference: 341/508

Oil tank small Lama 1:4

dimensions: 5.45 x 1.66 x 5.36 cm

Reference: 330/31

Bubble window for Lama

Bubble window for Lama Ord.No. 3300 / 3400 / 3401, Rotor ø 2500 mm

Reference: 30/50

Fire extinguisher approx. 70 mm long

Fire extinguishers in the cockpit are mandatory for any scale model helicopter, since the full-size machines are also required to carry them.Our fire extinguisher is available in two different sizes, and it can be mounted in the cockpit in a wide variety of positions.For models up to 2000 mm rotor diameter we recommend the smaller version; the bigger one...

Reference: 134/411

Antena alrededor de 1: 4

Reference: 341/417

Large mirror Lama 1:4

dimensions: 4 x 5.4 x 1 cm

Reference: 330/2

Dummy turbine, GRP

The dummy turbine provides the ideal starting point if you wish to install additional scale fittings on your Lama.The dummy turbine is assembled from six separate GRP mouldings, and fits all models with VR-22 mechanics installed.In the turbine-powered version of the Lama the actual turbine is located in this position.GRP dummy turbineLength approx. 490 mm

Reference: 1/21

Helmet for pilot William 1:4

As you would expect, we can also supply the matching type of GRP helmet for William the Pilot; it is simply pushed into place on his head. If you wish to fit a radio headpiece, you now have plenty of scope for your imagination: a piece of foam rubber, a thin wire mount and a coiled cable are all you need to make this accessory, and the pilot will...

Reference: 134/460

Telephone on board 1:4

dimensions: 1.9 x 1.2 x 6.3 cm

Reference: 330/5

Fittings set Bell 47 G III, Lama

Door fittings for large-scale model helicopters do not differ fundamentally from one type to another. However, the size of these accessories is important if the model is to look convincing, otherwise they will look out of scale.Compare the door handle of the Lama with that of the Alouette II, and the difference is obvious.The door fittings set for the...

Reference: 341/409

BTP Lama 1: 4

Reference: 340/2

Scale accessories for Lama Turbine

The suckering ducts are on the model exactly on the same place as the original ones in position to the turbine on the full-size helicopter.

Reference: 341/520

Battery housing /Lama

dimensions: 7.76 x 3.4 x 5.3 cm

Reference: 330/10

Cabin sheath for Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Reference: 134/444

Winch connections 1:4

dimensions:flat: 1.53 x 1.53 x 0.7 cmhigh: 1.29 x 1.29 x 1.14 cmPackage contains: 3x flat + 4x high

Reference: 340/1

Wheel holder for Lama

The Lama is a large helicopter, and the supplementary wheels which can be attached to the landing gear make it much easier to move the machine into and out of the hangar. However, the wheels are removed prior to flying the model. These wheel holders for our model of the Lama are made of plastic and are simply glued to the 20 mm Ø skid tubes using UHU...

Reference: 341/404

Position lights Lama x2 1:4

dimensions: 4.5 x 3.2 x 1.8 cmPack of 2 (l/r)