Tool case set

Reference: 64/16

8 x 12 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 12 x 3.5 mmpack of...

Reference: 90/9

Assembly tray, 25-part

Appropriate precautions should always be taken every time you start working on your model, and one of them is to prepare a suitable temporary storage area for small and ultra-small components. These assembly trays are sub-divided into small compartments, allowing you to sort components according to the stage of construction, while a second tray is used to...

Reference: 116/8

Silicone hose

The operating temperature of a tuned pipe or of a silencer has a destructive influence on their supports, if no heat resitant material is used when fixing.Silicone hose11 mm I.D.length approx. 300 mm

Reference: 71/11

Flanged ballrace 3 x 7 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Reference: 16/3

Spray can holder

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Reference: 55/7

Thrust bearing 12 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing12 x 25 x 6 mm3-part

Reference: 330/18

Gear support for tail drive

Component part for fuselages like Air-Crane, Bell 47 or Lama.Pack of 3

Reference: 68/1

Swivel bearing 10 x 19 x 9 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 10 x 19 x 9 mmpack of 1

Reference: 75/1

10 x 26 x 8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 26 x 8 mmpack of...

Reference: 870/49

Servo frame CFK

Reference: 55/1

10 x 19 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 19 x 5 mmpack of...

Reference: 38/1

6 x 19 x 6 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 19 x 6 mmpack of...

Reference: 4302

Glow plug Enya 6

Content of the package1 piecehot engine - cold plug (Summer) cold engine - hot plug (Winter)

Reference: 55/9

ball bearing 12 x 28 x 7 mm

Not available

Reference: 55/8

12 x 28 x 8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 12 x 28 x 8 mmpack of...

Reference: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...