Home

Filtra per

Disponibilità

Disponibilità

Prezzo

Prezzo

  • 5,00 € - 55,00 €

Categorie

Categorie

Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Tutte le migliori vendite
Attrezzi / Colle / Lubrificanti

Attrezzi / Colle / Lubrificanti

Attrezzi / Colle / Lubrificanti

Ci sono 37 prodotti.

Ordina per:
Rilevanza Nome, da A a Z Nome, da Z ad A Prezzo, da meno caro a più caro Prezzo, da più caro a meno caro
Visualizzati 1-12 su 37 articoli

Filtri attivi

  • Categorie: Attrezzatura specifica
  • Categorie: Pinze e cutters
Sanding sponge Anteprima

Riferimento: 10/77

Sanding sponge

Recensioni: 0

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Prezzo 5,50 €
Più
In vendita su richiesta
Circlip pliers Anteprima

Riferimento: 11/27

Circlip pliers

Recensioni: 0

Installing and removing the circlip on the main rotor shaft, these circlip pliers do the job and will not damage the circlip. The prongs of the pliers fit exactly in the holes in the circlip and open it evenly, without over-stressing it, so that it can safely be re-used. If you use other tools such as screwdrivers etc. the circlip is easily damaged or...

Prezzo 36,50 €
Più
In vendita su richiesta
Ball-link driver with handle Anteprima

Riferimento: 107/0

Ball-link driver with handle

Recensioni: 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Prezzo 27,40 €
Più
In vendita su richiesta
Wire cutters for steel wire Anteprima

Riferimento: 11/31

Wire cutters for steel wire

Recensioni: 0

The 2 mm pushrod from the tail rotor servo to the tail rotor bellcrank is made of hardened steel, as is the 2 mm tail rotor shaft. If you need to cut this material to length you need wire cutters which cut cleanly. These wire cutters are the ideal tool for cutting hardened steel wire. Wear protective goggles!

Prezzo 54,60 €
Più
In vendita su richiesta
All-purpose pliers Anteprima

Riferimento: 11/37

All-purpose pliers

Recensioni: 0

With these practical, small general purpose pliers you can reach almost all your mechanical parts. These pliers rest nicely in your hand because of the non-slip grips. Overall length 12 cm

Prezzo 12,80 €
Più
In vendita su richiesta
Ball-link driver 5.5 Anteprima

Riferimento: 107/1

Ball-link driver 5.5

Recensioni: 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Prezzo 8,40 €
Più
In vendita su richiesta
Ball-link driver 4.0 Anteprima

Riferimento: 107/2

Ball-link driver 4.0

Recensioni: 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Prezzo 8,40 €
Più
In vendita su richiesta
Ball-link pliers Anteprima

Riferimento: 11/99

Ball-link pliers

Recensioni: 0

When you are carrying out maintenance work on your mechanics or adjusting the mechanical linkages, e.g. to reset blade tracking, you have to push the ball-links off their pivot balls.These special ball-link pliers help you carry out this little task easily and without damaging the links. It is made of high-quality steel, and can be used both to disconnect...

Prezzo 54,60 €
Più
In vendita su richiesta
Tool case Anteprima

Riferimento: 21/11

Tool case

Recensioni: 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prezzo 19,10 €
Più
In vendita su richiesta
Glazing panel shears straight Anteprima

Riferimento: 11/260

Glazing panel shears straight

Recensioni: 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prezzo 32,30 €
Più
In vendita su richiesta
Glasspaper file, flat Anteprima

Riferimento: 11/28

Glasspaper file, flat

Recensioni: 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prezzo 14,80 €
Più
In vendita su richiesta
Widia disc cutter Anteprima

Riferimento: 29/11

Widia disc cutter

Recensioni: 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prezzo 16,90 €
Più
In vendita su richiesta
Torna all'inizio

Seguici su Facebook

Facebook