Marchi

Nessuna marca

Fornitori

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 12,80 €
Più
In vendita su richiesta
Tutte le migliori vendite

Fuselage centre section for Lama

340/7
Valutazione 



Component part for fuselage Lama, Ord.No. 3300, 3400, and 3401.

910,00 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione



Component part for fuselage Lama, Ord.No. 3300, 3400, and 3401.

Dettagli del prodotto
340/7
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Fuselage centre section for Lama

Fuselage centre section for Lama



Component part for fuselage Lama, Ord.No. 3300, 3400, and 3401.

Scrivi la tua recensione
16 autres produits dans la même catégorie :

Référence: 3941/90

Servo mounting set

Commentaire(s): 0

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Prix 11,70 €
Détails
En vente sur demande

Référence: 74

O-ring 3 x 8 mm hard

Commentaire(s): 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prix 4,70 €
Détails
En vente sur demande

Référence: 3942

Servo packer

Commentaire(s): 0

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Prix 6,60 €
Détails
En vente sur demande

Référence: 3947

Quick-release servo mount

Commentaire(s): 0

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Prix 8,50 €
Détails
En vente sur demande

Référence: 97/9

Screw fitting pushrod connector

Commentaire(s): 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Prix 5,50 €
Détails
En vente sur demande

Référence: 330/10

Housse de protection pour Lama

Commentaire(s): 0

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Prix 54,60 €
Détails
En vente sur demande

Référence: 13/21

Magnets for speed regulator

Commentaire(s): 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prix 11,70 €
Détails
En vente sur demande

Référence: 3948

Servo numbers

Commentaire(s): 0

Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30

Prix 9,70 €
Détails
En vente sur demande

Référence: 3936/1

Y-lead

Commentaire(s): 0

If you want to operate two servos in parallel from one receiver channel you requires a Y-lead.

Prix 14,80 €
Détails
En vente sur demande

Référence: 33/28

Rotor blade tie-down

Commentaire(s): 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Prix 26,60 €
Détails
En vente sur demande

Seguici su Facebook