Fuselage centre section for Lama

Riferimento: 18/11

Aluminium tube 5.5 x 4.4 x 1000 mm

Aluminium tube 5.5 x 4.4 x 1000 mm

Riferimento: 33/4

Rotor bolsa de cuchillas 4 cuchillas Ø 2500 mm

Riferimento: 13/21

Magnets for speed regulator

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Riferimento: 3944

Servo mount 120°

When using a 4-point-linkage, the linkages from the servos run in a straight line to the swashplate.A 3-point-linkage does not permit this, here the linkages run diagonally.The 120° servo mounting enables inclined installation of the servos, and the results are straight running linkages to the swashplate.All Sky Fox based mechanics as well as on the...

Riferimento: 15/8

Charge lead MPX high current plug 2.5 mm²

Not available

Riferimento: 1414

Battery Switch

Dual power supply with gas cap switch

Riferimento: 3947

Quick-release servo mount

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Riferimento: 33/22

Rotor blade support

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Riferimento: 603/19

Adaptor, tail boom rear, GRP

Component part for fuselages, Ord.No. 6030 or 6031.

Riferimento: 8/3

Tail rotor flange

The GRP tail rotor flange is used in full-fuselage helicopters such as the Jet Ranger, Bell 222 etc. to attach the tail rotor to the tail boom. The flange is supplied oversized, so that it can be fitted in all fuselages. Simply trim it to match the inside shape of the tail end of the fuselage, then glue it in place using Poxan-622 or UHU-Plus, and fitted...

Riferimento: 3941/90

Servo mounting set

Rubber servo mounting grommets absorb vibration and also help to protect the servos.Servo mounting set, for 2 JR servos

Riferimento: 18

PVC tube 3.2 x 2.2 x 1000 mm, white

PVC tube 3.2 x 2.2 x 1000 mm, white

Riferimento: 3935/4

Servo extension lead 700 mm

When extending servo cables take into account that cable lengths over 500 mm requires a suppressor (Ord.No. 1040) to avoid interference.

Riferimento: 1413

Electronic switch harness

Not available

Riferimento: 330/10

Protezione capottina per Lama

This protective sheath provides effective protection to the cabin of your valuable helicopter, and helps to avoid unsightly scratches. It is simply pulled over the cabin and closed with a hook -and-loop fastener.Cabin sheath for Lamamatching the cabins of the models 3300 and 3400

Riferimento: 33/27

Rotor blade tie-down large

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...