Home
Marchi

Nessuna marca

Fornitori
Migliori vendite
Flanged ballrace 6 x 10 x 3 mm Anteprima

Riferimento: 92/91

Flanged ballrace 6 x 10 x 3 mm

Recensioni: 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prezzo 14,70 €
Più
In vendita su richiesta
Aste 3,0 x 75 mm Anteprima

Riferimento: 70/76

Aste 3,0 x 75 mm

Recensioni: 0

Ready-made pushrod, threaded M 3. Content of the package: 1 piece

Prezzo 6,30 €
Più
In vendita su richiesta
Tutte le migliori vendite

Hole cutter up to 16 mm Ø

11/64
Valutazione 

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes.
Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings.
This hole cutter does an excellent job.
Hole cutter, up to 16 mm.

Here a few hints for making perfect small sized holes with the cone shaped hole cutter 11/64:
Take an old used o-ring, for instant Ord.No. 74/5, and push it over the hole cutter to a position of your desired hole diameter. Just stop cutting as the o-ring is getting close to the surface you are working on.
Another easy methode is to make a mark with a felt pen at the proper diameter and stop cutting at the mark.

54,60 €
Tasse incluse
Quantità
In vendita su richiesta

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descrizione

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes.
Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings.
This hole cutter does an excellent job.
Hole cutter, up to 16 mm.

Here a few hints for making perfect small sized holes with the cone shaped hole cutter 11/64:
Take an old used o-ring, for instant Ord.No. 74/5, and push it over the hole cutter to a position of your desired hole diameter. Just stop cutting as the o-ring is getting close to the surface you are working on.
Another easy methode is to make a mark with a felt pen at the proper diameter and stop cutting at the mark.

Dettagli del prodotto
11/64
Recensioni

Ancora nessuna recensione da parte degli utenti.

Scrivi la tua recensione

Hole cutter up to 16 mm Ø

Hole cutter up to 16 mm Ø

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes.
Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings.
This hole cutter does an excellent job.
Hole cutter, up to 16 mm.

Here a few hints for making perfect small sized holes with the cone shaped hole cutter 11/64:
Take an old used o-ring, for instant Ord.No. 74/5, and push it over the hole cutter to a position of your desired hole diameter. Just stop cutting as the o-ring is getting close to the surface you are working on.
Another easy methode is to make a mark with a felt pen at the proper diameter and stop cutting at the mark.

Scrivi la tua recensione
16 andere Artikel in der gleichen Kategorie:

Seguici su Facebook

Facebook