Hole cutter up to 16 mm Ø

Riferimento: 11/26

Cizallas para paneles de acristalamiento

Riferimento: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Riferimento: 11/53

Ridge cutter

Use this small ridge cutter to remove sharp burrs and edges from aluminium and plastics; e.g. remove sharp edges from an aluminium pipe.

Riferimento: 11/28

Glasspaper file, flat

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Riferimento: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Riferimento: 64/2

Flywheel puller

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Riferimento: 70/22

Die M 3.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Riferimento: 21/11

Tool case

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Riferimento: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Riferimento: 107/1

Ball-link driver 5.5

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Riferimento: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Riferimento: 11/36

Disc cutter set

Disc cutter set pack of 5 normal variation Wear protective goggles!

Riferimento: 11/80

Pipe bending tool

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Riferimento: 11/86

Pushrod measuring holder

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Riferimento: 11/59

Juego de herramientas de corte (bisturí + regla)

Riferimento: 10/77

Sanding sponge

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.