Home

Filter By

Availability

Availability

Price

Price

  • 5.00€ - 100.00€

Categories

Categories

Brands

No brand

Suppliers
Best Sellers
Flanged ballrace 6 x 10 x 3 mm Quick view

Reference: 92/91

Flanged ballrace 6 x 10 x 3 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Price 14.70€
More
On sale upon request
All best sellers

There are 42 products.

Sort by:
Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low
Showing 25-36 of 42 item(s)

Active filters

  • Availability: In stock
  • Categories: Specific Aids
  • Categories: Tool Sets
Tubing cutter, up to 15 mm Ø Quick view

Reference: 11/60

Tubing cutter, up to 15 mm Ø

Review(s): 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Price 33.30€
More
On sale upon request
Hole cutter up to 16 mm Ø Quick view

Reference: 11/64

Hole cutter up to 16 mm Ø

Review(s): 0

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Price 54.60€
More
On sale upon request
Soft sanding paper Quick view

Reference: 11/65

Soft sanding paper

Review(s): 0

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Price 9.70€
More
On sale upon request
Pipe bending tool Quick view

Reference: 11/80

Pipe bending tool

Review(s): 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Price 44.30€
More
On sale upon request
Pushrod measuring holder Quick view

Reference: 11/86

Pushrod measuring holder

Review(s): 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Price 14.80€
More
On sale upon request
Three-armed gripper Quick view

Reference: 9/11

Three-armed gripper

Review(s): 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Price 11.70€
More
On sale upon request
Die M 2.5 HSS Quick view

Reference: 70/20

Die M 2.5 HSS

Review(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Price 46.10€
More
On sale upon request
Die M 2.0 HSS Quick view

Reference: 70/21

Die M 2.0 HSS

Review(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Price 54.60€
More
On sale upon request
Die M 3.0 HSS Quick view

Reference: 70/22

Die M 3.0 HSS

Review(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Price 37.80€
More
On sale upon request
Protective goggles Quick view

Reference: 9/5

Protective goggles

Review(s): 0

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Price 14.80€
More
On sale upon request
File set with handle, six-part Quick view

Reference: 90/10

File set with handle, six-part

Review(s): 0

This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.

Price 17.00€
More
On sale upon request
Back to top

Follow us on Facebook

Facebook