Marques

No brand

Fournisseurs

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 12,80 €
Détails
En vente sur demande
Toutes les meilleures ventes

Il y a 33 produits.

Affichage 13-24 de 33 article(s)

Filtres actifs

Référence: 11/56

Glasspaper file, concave / convex

Commentaire(s): 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prix 12,80 €
Détails
En vente sur demande

Référence: 11/60

Tubing cutter, up to 15 mm Ø

Commentaire(s): 0

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Prix 33,30 €
Détails
En vente sur demande

Référence: 11/64

Hole cutter up to 16 mm Ø

Commentaire(s): 0

There are far more holes to be drilled in a helicopter fuselage than just the ordinary air inlet holes. Think of the access holes for the needle valve and the glow plug, openings for the exhaust manifold and the initial stage of cutting window openings. This hole cutter does an excellent job. Hole cutter, up to 16 mm. Here a few hints for making perfect...

Prix 54,60 €
Détails
En vente sur demande

Référence: 11/80

Pipe bending tool

Commentaire(s): 0

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Prix 44,30 €
Détails
En vente sur demande

Référence: 11/86

Pushrod measuring holder

Commentaire(s): 0

Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers

Prix 17,29 €
Détails
En vente sur demande

Référence: 9/11

Three-armed gripper

Commentaire(s): 0

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Prix 11,70 €
Détails
En vente sur demande

Référence: 70/20

Die M 2.5 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 46,88 €
Détails
En vente sur demande

Référence: 70/21

Die M 2.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 55,51 €
Détails
En vente sur demande

Référence: 70/22

Die M 3.0 HSS

Commentaire(s): 0

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Prix 38,43 €
Détails
En vente sur demande

Suivez-nous sur Facebook