Estabilizador horizontal para GRP Lama

Référence: 96/1

5 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 5 x 13 x 5 mmpack of...

Référence: 920/50

Front door set for Agusta

Component part for fuselage Agusta, Ord.No. 9020 and 9021.

Référence: 830/42

Exhaust mount 42 mm

  For silencer Ord.No. 116/96.Content of the package1 piece

Référence: 116/94

Silencer for 116/95

Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm

Référence: 64/33

bell pinion gear 23-tooth

Clutch bell pinion gear23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch

Référence: 116/8

Silicone hose

The operating temperature of a tuned pipe or of a silencer has a destructive influence on their supports, if no heat resitant material is used when fixing.Silicone hose11 mm I.D.length approx. 300 mm

Référence: 116/98

Manifold 34 mm

The various exhaust manifolds differ in shape and in the size of the flange, to match different engines' exhaust stubs. The term "exhaust hole spacing" refers to the holes on either side of the exhaust port, measured between hole centres.Please check before you order that you have selected the correct manifold to match your model and engine. Measure again...

Référence: 68/51

Swivel bearing 12 x 22 x 10 mm

A swivel bearing is fitted with a ball which is capable of rotation in all directions; this application is used in the swashplate. The dimensions of a swivel bearing mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Swivel bearing 12 x 22 x 10 mmpack of 1

Référence: 64/32

pinion gear 23-tooth

Clutch pinion gearincl. flywheel and split taper collet23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor

Référence: 870/53

Bearing plate, GFK

Not available

Référence: 7/17

6 x 16 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 16 x 5 mmpack of...

Référence: 68/2

20 x 32 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 20 x 32 x 7 mmpack of 1 

Référence: 38/4

Ball bearing 6 x 12 x 4 mm

Not available

Référence: 94/6

Thrust bearing 6 x 10 x 3 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 6 x 10 x 3...

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Référence: 870/49

Servo frame CFK