Soporte para tubo de escape de X-Treme

Reference: 90/9

Assembly tray, 25-part

Appropriate precautions should always be taken every time you start working on your model, and one of them is to prepare a suitable temporary storage area for small and ultra-small components. These assembly trays are sub-divided into small compartments, allowing you to sort components according to the stage of construction, while a second tray is used to...

Reference: 84

3 x 10 x 4 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 10 x 4 mmpack of...

Reference: 55/3

Thrust bearing 10 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing 10 x 25 x 6...

Reference: 71/19

2.5 x 8 x 2.8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 2.5 x 8 x 2.8 mmpack of...

Reference: 16/3

Spray can holder

This spray can holder can be used with any spray can, and makes it easier to apply the paint evenly. The holder provides an effective means of controlling the spray coat; an additional advantage is that your hands stay clean, as they don't make contact with the paint.

Reference: 830/42

Exhaust mount 42 mm

  For silencer Ord.No. 116/96.Content of the package1 piece

Reference: 64/16

8 x 12 x 3.5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 12 x 3.5 mmpack of...

Reference: 75/1

10 x 26 x 8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 26 x 8 mmpack of...

Reference: 75

8 x 16 x 4 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 16 x 4 mmpack of...

Reference: 870/49

Servo frame CFK

Reference: 11/66

Crankshaft nut socket spanner 10 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 10 mm, for O.S.

Reference: 10/73

Five minute epoxy, 50 ml

The more you build, the more frequently you use epoxies, whose components must be proportionately mixed. When you insert cartridges into the dispenser and press the components through the mixing nozzle the epoxy is ready for immediate use. Pack of 50 ml, pot life approx. 5 minutes

Reference: 116/94

Silencer for 116/95

Silencer, aloneIntake pipe 170 mmSilencer chamber 195 mmOverall Ø 50 mm

Reference: 64/33

bell pinion gear 23-tooth

Clutch bell pinion gear23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch

Reference: 715/80

Steel manifold for Mizar

 Steel manifold for Mizar with petrol engine34 mm hole spacinge.g. for ZG22 or G230

Reference: 39

8 x 22 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 22 x 7 mmpack of...