Ninguna marca
Referencia: 92/91
Brida rodamientos autolubricantes 6 x 10 x 3 mm
Política de seguridad
Política de envío
Política de devolución
No hay reseñas de clientes en este momento.
Reference: 11/80
A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm
Reference: 11/34
Rotor blades for large-scale model helicopters must be secured using screws of the appropriate size. Normally M4 bolts are employed, but here the usual size is M6. The T-handle of this M6 allen key provides plenty of torque, but you should only tighten the screws to the point where the blades can still align themselves at start-up.
Reference: 11/36
Disc cutter set pack of 5 normal variation Wear protective goggles!
Reference: 830/2
Extractor screwkey size 13for flywheel and split tapper collet on petrol engines
Reference: 11/86
Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.Pushrod measuring holderpack of 2holders fit any standard calipers
Reference: 11/28
If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...
Reference: 10/77
The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.
Reference: 107/1
This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket. Ball-link driverfor 5.5 mm socket spanner
Reference: 90/10
This special file set is particularly useful when you are cutting small openings, as they can be used to work on the tiniest of radii and straight edges. The rotary-action handle makes quick work of swapping individual tools. The collet can also be used to grip drills and taps of 2 to 5 mm ∅.
Reference: 107/0
This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket. Ball-link driverwith telescopic handle 11/44
Reference: 29/11
Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...
Reference: 11/65
For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5
Reference: 107/2
This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket. Ball-link driverfor 4 mm telescopic handle.
Reference: 64/2
If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...
