File set with handle, six-part

Reference: 11/26

Cizallas para paneles de acristalamiento

Reference: 11/80

Pipe bending tool

A versatile bending tool for fuel tank pipes, dummy collective pitch sticks in the cockpit etc. The tool is useful for tubes or pushrods with a diameter of 3.0 and 3.2 mm

Reference: 11/36

Disc cutter set

Disc cutter set pack of 5 normal variation Wear protective goggles!

Reference: 11/60

Tubing cutter, up to 15 mm Ø

The tubing cutter can handle aluminium, stainless steel and brass tubing up to 15 mm diameter. It can also be used to form a slight internal burr on tubing. For example if you use a tail rotor pushrod running in a PTFE sleeve in aluminium tubing, you can cut the aluminium to length at both ends with the tubing cutter, and the PTFE sleeve will not slip out.

Reference: 107/2

Ball-link driver 4.0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Reference: 11/57

Abrasive tape, 60 cm

 Replacement sanding strip60 cm roll

Reference: 90/7

Hammer, weight 230 g

How do you fix anything to a wooden component using a metric machine screw? The answer is to fit a captive nut as follows: Drill a hole of the right size to accept the nut barrel, then drive the nut's projecting teeth into the wood using a hammer and fairly gentle force; the captive nut is correctly fitted when its disc rests squarely on the surface of...

Reference: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Reference: 64/2

Flywheel puller

If the flywheel of the clutch is sitting to tight on the tapper of the collet you can use this flywheel puller.For this purpose you remove the nut from the crankshaft, then put the puller on the crankshaft, and turn both socket-head cap screws equally approx. 5 mm into the thread of the flywheel; the flywheel loosens now.The length of the socket-head cap...

Reference: 107/0

Ball-link driver with handle

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Reference: 11/53

Ridge cutter

Use this small ridge cutter to remove sharp burrs and edges from aluminium and plastics; e.g. remove sharp edges from an aluminium pipe.

Reference: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Reference: 70/20

Die M 2.5 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Reference: 11/65

Soft sanding paper

For preparing the GRP surface prior to the paintingP400dimensions: 11.5 x 15 cmPack of 5

Reference: 70/21

Die M 2.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Reference: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...