Epoxy 5 minutos, 50 ml

Riferimento: 830/42

Exhaust mount 42 mm

  For silencer Ord.No. 116/96.Content of the package1 piece

Riferimento: 11/67

Crankshaft nut socket spanner 14 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 14 mm, for O.S. 4-stroke

Riferimento: 71/11

Flanged ballrace 3 x 7 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Riferimento: 64/33

bell pinion gear 23-tooth

Clutch bell pinion gear23-toothmodule 1material: aluminiumtwin ballracedincl. clutch liningfits the glow plug motor clutch

Riferimento: 39

8 x 22 x 7 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 8 x 22 x 7 mmpack of...

Riferimento: 71/16

3 x 7 x 3 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 3 x 7 x 3 mmpack of...

Riferimento: 117/8

Thrust bearing 8 x 15 x 5 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Thrust bearing 8 x 15 x 5...

Riferimento: 71/19

2.5 x 8 x 2.8 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 2.5 x 8 x 2.8 mmpack of...

Riferimento: 870/49

Servo frame CFK

Riferimento: 39/2

10 x 22 x 6 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 10 x 22 x 6 mmpack of...

Riferimento: 17/22

6 x 13 x 5 mm

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness.  Ballrace 6 x 13 x 5 mmpack of...

Riferimento: 870/53

Bearing plate, GFK

Not available

Riferimento: 920/50

Front door set for Agusta

Component part for fuselage Agusta, Ord.No. 9020 and 9021.

Riferimento: 11/66

Crankshaft nut socket spanner 10 mm

If you want to tighten the crankshaft nut on your engine fully, and still be able to loosen it again without problems, you need the correct size of crankshaft socket spanner. Note, however, that different engines require different sizes, so take care to order the correct item. Crankshaft nut socket spanner 10 mm, for O.S.

Riferimento: 55/7

Thrust bearing 12 x 25 x 6 mm

High centrifugal forces cannot be absorbed by a radial bearing. For that application we use a 3-part thrust bearing (axial bearing) consisting of a loose ring, a ball cage and a fixed ring: the parts are installed in this sequence.The dimensions of a ballrace mean:inside diameter (I.D.) x outside diameter (O.D.) x thickness.Thrust bearing12 x 25 x 6 mm3-part

Riferimento: 55/2

Bearing 8 x 19 x 6 mm

Not available