Accueil

Filtrer par

Disponibilité

Disponibilité

Prix

Prix

  • 5,00 € - 55,00 €

Catégories

Catégories

Marques

No brand

Fournisseurs
Meilleures Ventes
Flanged ballrace 6 x 10 x 3 mm Aperçu rapide

Référence: 92/91

Flanged ballrace 6 x 10 x 3 mm

Commentaire(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Prix 14,70 €
Détails
En vente sur demande
Toutes les meilleures ventes
Outillages/colles/lubrifiants

Outillages/colles/lubrifiants

Outillages/colles/lubrifiants

Il y a 37 produits.

Trier par :
Pertinence Nom, A à Z Nom, Z à A Prix, croissant Prix, décroissant
Affichage 1-12 de 37 article(s)

Filtres actifs

  • Catégories : Accessoires spécifiques
  • Catégories : Pinces
Sanding sponge Aperçu rapide

Référence: 10/77

Sanding sponge

Commentaire(s): 0

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Prix 5,50 €
Détails
En vente sur demande
Circlip pliers Aperçu rapide

Référence: 11/27

Circlip pliers

Commentaire(s): 0

Installing and removing the circlip on the main rotor shaft, these circlip pliers do the job and will not damage the circlip. The prongs of the pliers fit exactly in the holes in the circlip and open it evenly, without over-stressing it, so that it can safely be re-used. If you use other tools such as screwdrivers etc. the circlip is easily damaged or...

Prix 36,50 €
Détails
En vente sur demande
Ball-link driver with handle Aperçu rapide

Référence: 107/0

Ball-link driver with handle

Commentaire(s): 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverwith telescopic handle 11/44

Prix 27,40 €
Détails
En vente sur demande
Wire cutters for steel wire Aperçu rapide

Référence: 11/31

Wire cutters for steel wire

Commentaire(s): 0

The 2 mm pushrod from the tail rotor servo to the tail rotor bellcrank is made of hardened steel, as is the 2 mm tail rotor shaft. If you need to cut this material to length you need wire cutters which cut cleanly. These wire cutters are the ideal tool for cutting hardened steel wire. Wear protective goggles!

Prix 54,60 €
Détails
En vente sur demande
Ball-link driver 5.5 Aperçu rapide

Référence: 107/1

Ball-link driver 5.5

Commentaire(s): 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 5.5 mm socket spanner

Prix 8,40 €
Détails
En vente sur demande
All-purpose pliers Aperçu rapide

Référence: 11/37

All-purpose pliers

Commentaire(s): 0

With these practical, small general purpose pliers you can reach almost all your mechanical parts. These pliers rest nicely in your hand because of the non-slip grips. Overall length 12 cm

Prix 12,80 €
Détails
En vente sur demande
Ball-link driver 4.0 Aperçu rapide

Référence: 107/2

Ball-link driver 4.0

Commentaire(s): 0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Prix 8,40 €
Détails
En vente sur demande
Ball-link pliers Aperçu rapide

Référence: 11/99

Ball-link pliers

Commentaire(s): 0

When you are carrying out maintenance work on your mechanics or adjusting the mechanical linkages, e.g. to reset blade tracking, you have to push the ball-links off their pivot balls.These special ball-link pliers help you carry out this little task easily and without damaging the links. It is made of high-quality steel, and can be used both to disconnect...

Prix 54,60 €
Détails
En vente sur demande
Tool case Aperçu rapide

Référence: 21/11

Tool case

Commentaire(s): 0

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Prix 19,10 €
Détails
En vente sur demande
Glazing panel shears straight Aperçu rapide

Référence: 11/260

Glazing panel shears straight

Commentaire(s): 0

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Prix 32,30 €
Détails
En vente sur demande
Glasspaper file, flat Aperçu rapide

Référence: 11/28

Glasspaper file, flat

Commentaire(s): 0

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Prix 14,80 €
Détails
En vente sur demande
Widia disc cutter Aperçu rapide

Référence: 29/11

Widia disc cutter

Commentaire(s): 0

Widia produced a tungsten carbide, derived from "like diamond - Wie Diamant (Ger)". The first Widia tools were available on the open market in 1923. They consisted at that time of approx. 94 % tungsten carbide and 6 % cobalt. Today's types contain additives that improve the hardness etc. The Widia disc cutter is ideal for cutting clean-edged openings in...

Prix 16,90 €
Détails
En vente sur demande
Retour en haut

Suivez-nous sur Facebook

Facebook