Tubing cutter, up to 15 mm Ø

Référence: 70/22

Die M 3.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Référence: 21/11

Tool case

Tool case, complete empty, alone, including foam to cutsize approx. 275 x 230 x 83 mm

Référence: 34/9

Tail blade balance shaft

If the tail rotor blades are to be balanced accurately, the assembled hub must be included in the balance process. Now you can balance the tail rotor perfectly, and the unit's smooth running will prove it!

Référence: 9/11

Three-armed gripper

This handy three-armed gripper acts as a finger-extension for placing screws and nuts in difficult, small and inaccessible places.  Three-armed grippertotal length 115 mm

Référence: 11/53

Ridge cutter

Use this small ridge cutter to remove sharp burrs and edges from aluminium and plastics; e.g. remove sharp edges from an aluminium pipe.

Référence: 11/260

Glazing panel shears straight

These powerful, sharp shears simplify the task of cutting out vacuum-moulded bodywork components. Glazing panels, dummy fuel tanks etc. are easily cut out along the moulded-in lines using these special shears. We suggest not to cut out anything until you satisfy yourself with the exact dimensions. This is because GRP parts (fuselages etc.) are hand made...

Référence: 11/57

Abrasive tape, 60 cm

 Replacement sanding strip60 cm roll

Référence: 9/5

Protective goggles

When handling tools it is in your own interests to read and observe the safety information and constantly to be aware of the possible hazards, before you have a really close encounter with a workpiece which, for whatever reason, flies off. Wear these protective goggles when grinding, turning and machining, and also when you are cutting off steel rod....

Référence: 11/28

Glasspaper file, flat

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Référence: 70/21

Die M 2.0 HSS

Our easy-to-use dies are made of top-quality HSS steel. The bevelled entry to the dies ensures that the thread always starts exactly "square" and cuts cleanly. Good thread-cutting oil is as important as the die itself, as it extends the useful life of the tool several times over.

Référence: 11/26

Cizallas para paneles de acristalamiento

Référence: 107/2

Ball-link driver 4.0

This tiny tool is designed to help you screw pushrods into ball-links. It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.  Ball-link driverfor 4 mm telescopic handle.

Référence: 10/77

Sanding sponge

The primary use for abrasive sponges is for large-area sanding of wooden and GRP components, but they are also excellent for rubbing down filled surfaces when used wet. Abrasive sponges are also useful for fine-sanding of components with sharp edges and rounded surfaces.

Référence: 830/2

Extractor screw

Extractor screwkey size 13for flywheel and split tapper collet on petrol engines

Référence: 11/56

Glasspaper file, concave / convex

If you enjoy building full-fuselage models you cannot help but appreciate practical tools which make your work easier. The glasspaper file is ideal for final trimming of openings for windows, doors and vent grilles after machining them out. The file is 25 cm long overall, with a sanding area 13 cm long and 2.5 cm wide on each side. The file is supplied...

Référence: 90/7

Hammer, weight 230 g

How do you fix anything to a wooden component using a metric machine screw? The answer is to fit a captive nut as follows: Drill a hole of the right size to accept the nut barrel, then drive the nut's projecting teeth into the wood using a hammer and fairly gentle force; the captive nut is correctly fitted when its disc rests squarely on the surface of...