Home
Brands

No brand

Suppliers
Best Sellers
Flanged ballrace 6 x 10 x 3 mm Quick view

Reference: 92/91

Flanged ballrace 6 x 10 x 3 mm

Review(s): 0

Ballraces are used wherever moving parts are required to run with a minimum of play and a minimum of friction. The more ballraces are used, the more smoothly the mechanics of a helicopter works, and the lower the rate of wear. The dimensions of a ballrace mean: inside diameter (I.D.) x outside diameter (O.D.) x thickness. For flanged bearings the same...

Price 14.70€
More
On sale upon request
All best sellers

There are 420 products.

Sort by:
Relevance Name, A to Z Name, Z to A Price, low to high Price, high to low
Showing 97-108 of 420 item(s)

Active filters

Kevlartank for Kerosene 1.4 l Quick view

Reference: 26/50

Kevlartank for Kerosene 1.4 l

Review(s): 0

Aramid is a fibre that is used in motor racing. The tanks have an even surface inside and rough on the outside. These fuel tanks are all pressure tested to make sure that they are 100% leak-proof when they arrive at your workshop. They fit in every fuselage, that would normally use the plastic tank Ord.No. 26/5 for. For example, this Aramid tank is...

Price 349.10€
More
On sale upon request
Motor mount drilled for... Quick view

Reference: 59/2

Motor mount drilled for Rossi 11.5 cc

Review(s): 0

Factory-drilled motor mounts, already drilled and tapped for M 3 or M 4, are available in pairs (left / right). Avoid interchanging the left hand with the right hand one!1 pairfactory-drilled

Price 54.60€
More
On sale upon request
PTFE pipe 20 x 2.5 x 100 mm Quick view

Reference: 115/11

PTFE pipe 20 x 2.5 x 100 mm

Review(s): 0

Manifolds and tuned pipes or silencers must be installed without touching each other, because the contact of these metal parts could cause radio interference. We can refer to this interference as "electric noise". The connection by PTFE pipe enables the required distance of 10 - 15 mm in the prescribed position, and it steadily seals gas-tight. This...

Price 19.40€
More
On sale upon request
Shim spacer set Quick view

Reference: 59/20

Shim spacer set

Review(s): 0

To obtain the optimum clearance between clutch pinion and main gear you can use these shim spacers, which are 0.1 and 0.2 mm thick. Simply loosen the engine retaining screws and place the appropriate shim spacer between engine and engine mount; suits all types of engine.Engine spacer set2 each 0.1 mm and 0.2 mm thick

Price 11.20€
More
On sale upon request
Exhaust for Bell 212 Twin Jet Quick view

Reference: 214/16

Exhaust for Bell 212 Twin Jet

Review(s): 0

Exhaust tubes for turbines are always designed for the specified model. It is important that no forward thrust emerges from the system. Should this still occur, the forward thrust produced is minimal.Turbine exhaust tubes are designed as exhaust-gas diffusers, i.e. opens wider towards the rear.

Price 552.50€
More
On sale upon request
Tuned pipe silencer Quick view

Reference: 116/65

Tuned pipe silencer

Review(s): 0

 Tuned pipe silenceroverall length 350 mmconnection-Ø 20 mmoverall Ø 50 mmsilencer chamber 170 mmweight approx. 160 gtail pipe length 90 mmcurved, for UH-1D

Price 153.40€
More
On sale upon request
Back to top

Follow us on Facebook

Facebook