Marcas

Ninguna marca

Los productos más vendidos

Adaptor, Tubo de cola de rear, GRP (Brazo trasero)

603/19
Valoración 
Adaptador, tubo de cola trasera, GRP
19,90 €
En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Adaptador, tubo de cola trasera, GRP
Detalles del producto
603/19
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Adaptor, Tubo de cola de  rear, GRP (Brazo trasero)

Adaptor, Tubo de cola de rear, GRP (Brazo trasero)

Adaptador, tubo de cola trasera, GRP
Escriba su propia reseña
16 other products in the same category:

Reference: 33/20

Rotor blade support

Review(s): 0

An easy solution to the transport problem: This rotor blade support fits all helicopter trainers with 20 mm O.D. tail booms.Rotor blade supportfor rotor blades up to 65 mm chord

Price 12.80€
More
On sale upon request

Reference: 33/22

Rotor blade support

Review(s): 0

If you do not wish to remove the rotor blades temporarily for transport, they can be protected effectively in this strong support, which is mounted above the tail boom.The height of the support, the width of the blade openings and the diameter of the tail boom are the crucial factors when buying a blade support.This support is ideal for pod-and-boom...

Price 14.80€
More
On sale upon request

Reference: 3942

Servo packer

Review(s): 0

Servo packing pieces are used with direct-linked JR / Graupner roll-axis servos to give clearance to the pitch-axis servo. Pack of 10

Price 6.60€
More
On sale upon request

Reference: 10/1

Dispenser for UHU plus endfest 300

Review(s): 0

Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.

Price 75.80€
More
On sale upon request

Reference: 33/28

Rotor blade tie-down

Review(s): 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Price 26.60€
More
On sale upon request

Reference: 18/10

PTFE tube for tail drive shaft

Review(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Price 12.80€
More
On sale upon request

Reference: 33/27

Rotor blade tie-down large

Review(s): 0

The rotor blade harness ranks as an essential accessory for full-size helicopters. These items prevent the blades swinging or rocking, and thereby exerting pressure on the rotor shaft. If that were to be allowed, in-flight failures could be attributed to it.Rotor blades set in motion by rising winds could also be damaged by striking obstacles. The rotor...

Price 32.60€
More
On sale upon request

Reference: 97/9

Screw fitting pushrod connector

Review(s): 0

Screw fixing pushrod connectors can be used on bell-cranks and servo output arms at the tail rotor servo, so that the tail rotor pushrod can quickly be installed, disconnected and adjusted. A further advantage is that a hardened steel pushrod can be used. For one helicopter you need two pushrod connectors.Caution during installation: the barrel of the...

Price 5.50€
More
On sale upon request

Reference: 33/25

Rotor blade support

Review(s): 0

Any easy solution to the transport problem: The cut-out of this rotor blade support accommodates to the different shapes of tail booms on fuselages.Rotor blade supportfor fuselages, 30 x 270 x 200 mm

Price 26.60€
More
On sale upon request

Reference: 3947

Quick-release servo mount

Review(s): 0

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Price 8.50€
More
On sale upon request