Marcas

Ninguna marca

Referencia: 060

Bulon 3.5 mm - M 2.0 x 5.0

Reseña(s): 0

Estos pernos de punta esférica ofrecen una conexión óptima entre un brazo de salida de servo GRP y la varilla de empuje a la mecánica. Debajo del brazo de salida, bloquea el perno de bola con una tuerca hexagonal M 2. Para brazos de salida de aluminio, utiliza pernos de punta esférica. 060/7 y fluido de bloqueo de hilo.

Precio 13,80 €
Más
En venta bajo pedido
Los productos más vendidos

Guia de metal 6.2 x 10 mm

17/2
Valoración 
Acero guía de 6,2 x 10 mm
9,20 €
Impuestos incluidos En venta bajo pedido
Cantidad
En venta bajo pedido

 

Política de seguridad

 

Política de envío

 

Política de devolución

Descripción
Acero guía de 6,2 x 10 mm
Detalles del producto
17/2
Reseñas

No hay reseñas de clientes en este momento.

Escriba su propia reseña

Guia de metal 6.2 x 10 mm

Guia de metal 6.2 x 10 mm

Acero guía de 6,2 x 10 mm
Escriba su propia reseña
16 autres produits dans la même catégorie :

Référence: 3947

Quick-release servo mount

Commentaire(s): 0

During construction we often need that "third hand", and there are times when it would be really useful to be able to see assemblies from front and rear at the same time.Servo installation is fast and reliable using the quick-release servo mount.The mounting plates are simply positioned either in front of the servo or behind it - whichever is more...

Prix 7,00 €
Détails
En vente sur demande

Référence: 3948

Servo numbers

Commentaire(s): 0

Cable spaghetti? We all know the problem of allocating the servo leads to the receiver outputs. Here's the answer: number them like the pro's do! Simply put the receiver channel number on each lead; they can be removed just as easily. The pack contains three sets of 10, numbered from 0-9, in different colours.Servo numbers, pack of 30

Prix 9,10 €
Détails
En vente sur demande

Référence: 74

O-ring 3 x 8 mm hard

Commentaire(s): 0

O-ring 3 x 8 mm hard Content of the package: 4 pieces Tip: O-rings always slide with a drop of silicone oil onto the shaft.

Prix 3,90 €
Détails
En vente sur demande

Référence: 33/28

Rotor blade tie-down

Commentaire(s): 0

Rotor blade tie-downs are an essential feature of full-size helicopter life. The tie-down protects the blades from swinging, rocking and stretching, and thereby prevents excessive pressure on the rotor shaft. If these measures were not taken the result could easily be in-flight mechanical failure; rotor blades spinning as the wind rises could strike...

Prix 22,10 €
Détails
En vente sur demande

Référence: 13/21

Magnets for speed regulator

Commentaire(s): 0

These magnets are suitable for use with all commercial speed regulators. For installation in the mechanics it is advisable the magnets be glued in a clamp ring Ord.No. 54/6, or as in the photo on the internal-tooth gear ring. Pack of 3

Prix 9,50 €
Détails
En vente sur demande

Référence: 18/10

PTFE tube for tail drive shaft

Commentaire(s): 0

PTFE is used as a bearing for the 2 mm wire tail drive shaft (Ord.No. 17) or as a support guide for the 2 mm piano wire push rod (Ord.No. 21 and 800/12) Length: approx. 740 mm

Prix 11,50 €
Détails
En vente sur demande

Référence: 10/1

Dispenser for UHU plus endfest 300

Commentaire(s): 0

Using the dispenser allows UHU plus endfest 300 to be allotted exactly, evenly and economically. The special feature of this dispenser is the enclosed mixing nozzle, which mixes the adhesive ready for use.

Prix 69,50 €
Détails
En vente sur demande